ender 3 control board fan 3d models

I swapped out the knob on the control panel of my Ender 3 with a miniature hand grenade. Initially, I neglected to insert a safety pin into it. ...You'll find both scenarios captured below for comparison purposes.

To give your Control Knob a major upgrade on our Ender 3 machine is easy. ...No special adhesive is required - this upgraded knob simply snaps into place securely on the original button with a precision fit.

The human-made fan guard serves as a protective barrier to prevent molten plastic from entering the Ender 3 printer's circuit board compartment.

I created an innovative control knob for your Ender 3 that enhances precision and rapid rotation. ... To assemble, print the knob with its surface facing downwards on the build plate and using TPU to ensure a snug, secure grip due to the precise...

This is a simple, yet cool upgraded media control knob for the Ender 3. This print is press fit, so when installing the new knob, a small amount of force will need to be applied to press the new knob on. I have included the Fusion 360 file so...

Ender 3 control knob reimagined as a faucet handle design. This upgrade replaces the stock part with a more user-friendly and visually appealing alternative, providing an improved turning experience. Update: - Version five exhibits a slightly...

I Imported the component into Tinkercad, then brought in the part I wanted to create a control knob for. ...Next, I made this part a hole and centered it, and combined the two to leave a hollow space where I could attach it to my Ender 3.

I discovered that the Ender-3 control box lid inlet hole for the fan was too small for the actual fan blades (35mm hole vs 39mm blades), resulting in some unusual turbulent effect which made the fan create quite a lot of noise when mounted, but...

Prusa Mini like control knob for the Ender 3 V2. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 0.2 Infill: 15% Filament: AmazonBasics PETG Orange Category: 3D Printer Parts

You'll need the following items to control your Ender-3 Pro panel: AC Power Meter: 80-260V 20A AC voltage, current, and power meter with blue backlight available at NL Aliexpress for 1 pc. Push Button: 12 MM push button on/off switch rated for up to...

This is just a simple knob to upgrade the existing media control knob on the Ender 3. This is a press fit knob so the fit is pretty tight. Don't get scared if it seems like it won't fit, it will, just give it a good press. I've included the...

Ender 3 enthusiast shields up! ...Customized Ender 3 fan guard + personalized Ender 3 moniker in one sleek design.

This mod involves swapping out the 50mm fan in the control box with a 60mm fan, installed parallel to the board directly above the heat sinks. By doing so, users can opt for a wider range of fans, including the popular Noctua series, and reap the...

Ender 3 ventilation cover to protect the fan. ... Ender 3 Lüftungsabdeckung zum Schutz des Lüfters.

Ender 3 Replacement Fan Blade. ... Print Tested: No.

 Easy to print Fan cover for Ender 3.

My first 3D model is fan cover for Ender 3

It relocates the stock control board fan to above the heat sink pulling fresh air from the vent and blowing it across the fin stack. The duct press fits on to the fin stack, fitment might be a little tight and the model might need some reworking...

A replacement for the mainboard housing that revolutionizes the Ender 3's electronics setup, consolidating everything into a single box efficiently cooled by a powerful 120mm fan. This upgrade replaces the noisy stock fans with a much quieter setup,...

This model is created to relocate the fan for the Ender 3 control board, to reduce the fan noise coming out from the vent. it can relocate the fan nearer to the center of the board (and the heatsink as well) without clearance issue. After printing...

I Made the Cap for my Ender 3 Pro. ...It shows the direction to turn up a value. Pretty simple bute awesome grip, takes under 2h to print. The Cap fits perfect on Ender 3 Pro (Bought 2021)

Ender-3 Fan block 3010 Fan * 3 M3 Nuts * 12 M3X16 Screws * 12 M3X10 Screws * 2

Designed by printXD for the Ender 3 pro and ender 3 Doesn't need any support but I suggest using a layer height of 0.16 or 0.12 for the best looking results. Go look at profile for more cool and interesting upgrades for the ender series printers. ... ...

Cooler cover on the control unit of the Ender 3

A remix of Ender-3 axis cheat badge by infooverload. ...This model is just a simple ender logo and is 1.5mm thick with logo at .5 thick for at total of 2mm thick.

I took a few other designs/models and diced them up into a new control panel for my Ender 3 Pro printer. It may fit the Ender 3 also, but it has "Pro" written on it. With the addition of the SD card reader and holder, everything is now right where it...

Remix of the original fan to fit the ender 3 hot end fan.

Here's a fan cover and MicroSD Card Adapter holder specifically designed for the Ender-3. To create this piece, I printed it with the front face facing downwards. ...This design is ideal for holding a full-size SD card to micro SD card adapter.

I didn't like the smooth knob that comes on the Ender 3 so I designed this cover that has grooves for great grip. This was intended to be printed with TPU filament. ...It just slides over the existing knob.

Just a basic fan cover for the Ender 3. Use some form of 2 sided tape to place over fan outlet on the boards cooling fan. No need to remove screws. 12-27-18 After printing the original I decided to reduce the height by 5mm. ...There is now 2 files, the...