ender 3 clips 3d models

... cables on the printer with ease. I produced this item using Geeetech Black PLA filament. You can see this clip featured in my YouTube video titled Six 3D Printed Upgrades for the Ender 3. ... This product is available through an affiliate link.

Say goodbye to annoying and ugly binder clips holding whatever build surface you use onto your Ender 3's heated bed. These clips are designed to fit snugly over each corner of your build plate, securely holding your factory glass/PEI sheet/standard...

20 x 20 V-Slot Cable Clip designed for Ender 3 v2. This can be made a custom length by scaling the Y (if face down) axis in your slicer. or X axis (if standing upright). ...

the clip for the main power wire on the ender 3 / 3 pro u can print it with any material to mount to plastic surface u can heat up both surfaces and just press them together else just use some hot glue / super glue / ca to mount

Power Cable Clip for Creality Ender 3. This remix is based on the original ribbon cable clip (https://www.thingiverse.com/thing:2880021), which works great for the ribbon cable and Y and X axis cables, but has one major issue - it's too small for...

Power cable clip for the Creality Ender 3. ***This is a remix from the original ribbon cable clip (https://www.thingiverse.com/thing:2880021) The original clip is great for the ribbon cable and the Y and X axis cables. The issue is that it is too...

I created a small usb holder for the stock sdcard reader. ...It clips into ender's rail.

This attachment is specifically engineered to be securely fastened onto the Ender 3 frame, ensuring that the power cable remains safely in place at all times. It's crucial to remember not to set the bed temperature too low when using this clip, as...

I have a reliable Ender 3 printer with a removable bed, which comes equipped with four convenient bulldog clips that securely attach to the heater. However, these clips can sometimes get in the way and obstruct access to the printer's interior. I...

The stock ender 3 level knob will move with printing. Previously use a red dot sticker to mark the position (red dot seen in my video). However, if the knob over-rotate, the red dot will not be able to tell me that the position is wrong. Thus I...

The stock ender 3 level knob will move with printing. Previously use a red dot sticker to mark the position (red dot seen in my video). However, if the knob over-rotate, the red dot will not be able to tell me that the position is wrong. Thus I...

This is a clip I made to hold an LED Strip for my Ender 3 V2. The LED strip it holds is linked be low but it should hold anything that will fit in the slot. Print with 50%+ infill with All supports. It prints best one at a time but when printing...

This is a lightweight clip that can be used with the Ender 3 to secure the bowden tube and wires from the hotend to the extruder / controller. The open hole should be occupied by the bowden tube and the two holes that have a cover should fit...

Secures the bowden tube's connector to the Creality Ender 3's frame assembly for a secure fit.

Ender 3 v2 Bowden clips. I used the MIKA3D Silk Copper because I was at the end of the spool and didn't feel like changing out. In the future, I would probably use Hatchbox Black. I would also probably change the quality from 0.2 to 0.16 just to...

I designed this hack for my official Creality Ender 3 (3mm) glass bed, opting to repurpose metal clip bands from the original clips that came with the printer instead of purchasing additional ones. ...This solution works seamlessly and can be easily...

A minimalist attachment designed specifically for mounting the standard Ender 3 control panel on top of dvilleneuve's sleek Duet 2 Wifi enclosure.

Designed in Fusion 360 in about 10 minutes, sliced with Cura 3.1.0, I created this to keep the hotend assembly cabling off my print bed and remove the weight of the cable from my PTFE tube on my Sainsmart Creality Ender 3. I use this along with...

This model is made to better guide the filament into a direct drive modded ender 3. ...Especially if the filament is in the middle of drying or a dry box.</p>

This model is made to better guide the filament into a direct drive modded ender 3. ...Especially if the filament is in the middle of drying or a dry box.

This is a clean cable holder that mounts to the z-axis motor of a ender 3 (pro). There are a couple of different versions available, depending on the tickness of the ring and the prefferd lenght of the screw. These prints are tested in PLA and it is...

Clips for fixing easily the glass bed

I required a larger clipping capacity.

A basic attachment for a 4mm template crystal on the Creality Ender series printer.

Simple remix offering some more room to clip the power cables.

This is a rail mounted cable clip useful in keeping accessory cables tidy and secure. ...The clip was specifically designed to manage the USB-C power cable for a Raspberry Pi power cable used for an OctoPrint node.

This is a rail mounted cable clip useful in keeping accessory cables tidy and secure. ...The clip was specifically designed to manage the USB-C power cable for a Raspberry Pi power cable used for an OctoPrint node.

Felt the clip was too long, so I shortened it in Tinkercad. Success? ... I think it is acceptable.

... I have designed some new clips that wrap the corners of the bed and have not given me any issues with bed temperatures around 70c and prints running as long as 36 hours. ... Here is a link to the new clips: https://www.thingiverse.com/thing:4745288

... text: Useful clip to help keep track of your USB sticks and SD cards. ... I've remixed some cable clips that can securely store an SD card or USB stick inside them. ...For optimal results, I recommend printing them on their side with supports enabled.