ender 3 case 3d models

customized with 3D Slash!

Since the original Fan cover doesn't fit, I created a new one. Printed it with a **0.5** nozzle and variable layer height (0.2-0.32). It can be printed **without support**. I put just a little in the entrance. ...Since the underside is not...

I removed the square holes for the switches and replaced them with a round hole for my own switch, and another hole for the cables. I also cut the fan duct because I use a standard Creality board (with this adapter...

This enclosure instead accommodates a balenaFin that can effortlessly operate OctoPrint directly off the 24-volt power supply provided by the printer itself.

I installed a 8010 fan outside, blowing in which I power proxy a buck converter. For the raspi (which has a temperature sensor available to check) the difference is dramatic - 50+°C w/o and 30+ with the fan running. I found no info wrt a temperature...

I remixed Michael's fantastic rear ender 3 case to fit an Orange Pi PC, using Orange Pi PCs for all my OctoPrint instances because they're more cost-effective than Raspberry Pi and offer the same performance, which is a major advantage when you have...

This is a remix of a remix of a Ender 3 Pro Case from Thingiverse that in turn is a remix of this case.  I redesigned it to better fit my SKR mini 2.0 and a Raspberry Pi 3 or 4.  I originally had some Pi version specific holes but opted to remove...

Raspberry Pi 3 Case designed to perfectly fit the Ender 3 by combining all the essential features I was looking for. It provides access to GPIO, fan mounting holes, and large openings for larger overmolded connectors. The Pi can be easily slid out of...

I installed a rail mount on my Ender 3 Pro's 2020 aluminum frame rails, and left the lower part of the design unchanged.

Hello, I was looking for a Raspberry Pi case to mount on my Ender 3 profiles and stumbled upon the thing from 0711nimajneB (https://www.thingiverse.com/thing:3454663). I had some switches lying around from my mechanical keyboard so I decided to use...

This is a custom version of the Ender 3 Pro case by xavinci.\r\n\r\nIt will accommodate the original mainboard that comes with the Ender 3 (Pro) and I have also modified the case to fit the Raspberry Pi, making it compatible with the Pi...

I bought the Raspberry PI to have Octoprint in my Ender 3 v2. The Pi that I bought came with a nice case and some accessories. ...Wanted to keep the case, so designed a holder for the Pi with the case and a mount for the camera with the case.

a case for camera OV3660 and ender 3 s1 bed mount

Ender 3 S1 - Raspberry Pi Cam Mount and Case for Cam.

External Case for the Displaypart of the Ender 3. You can put the Display everywhere you wish (as long the Cable is long enough) Take a little Glue to compare the two Parts or just put them together. I used Wood-PLA for the Bottom and PETG for the...

This is a mounting bracket to hold a GeeekPi raspberry pi case to an Ender 3 pro frame.

Custom lid for this case, for mounting onto Ender 3 3D printer. ...Compatible with Raspberry Pi Zero 2 W.

This is a case for the BTT SKR Pro v1.2 to be side mounted on ender 3 (Left side) You will need to mount the stock ender 3 screen to this case since the wires don't reach the screen original location. I designed a cover but still need some...

Slightly modded (smaller vent gaps) of the case by DotNetWorker Used Ender 3 bracket by FONSWERKS to make a slide-on mounting bracket for the rails of the Ender 3 V2 without blocking any ports. Bracket should fit snuggly around the Pi case, but still...

**Additional parts required** - M3 6mm screw x 3 - *(optional)* M3 8mm screw, M3 nut x 3 (to be used with https://www.thingiverse.com/thing:3050607 instead of stock M4 screws and tnuts) **Parts to print:** Both: - ender 3 v2 dwin case-Back.stl -...

# Octopi case for Raspberry Pi 3B+ I made this case because the other one didn't fit my Relais and my Buckconverter. For this project I'm using 2 Buckconverter and one 30A Relay for the PSU and one 10A Relay for my LED-Stripe. ## Schematic If...

If you need to make any adjustments, check out this link: https://www.tinkercad.com/things/iA152BNAwVB-rpi4-geekworm-case-ender3pro-holder The Geekworm RPI4 case can be found on Amazon at the following URL:...

A 20mm fan can be installed inside the case. The Raspberry Pi is attached with M2.5 * 8mm (self-tapping) screws. If you like the Remix, please leave a Like. I am always open to suggestions for improvements or changes. ...

This was designed for the Ender 3 Pro (may work with Ender 3, but I have not tried it, use at your own risk) All of my designs are unpaid passion projects that I choose to share, and I provide mesh models for free, but if you'd like to support me...

To use this specific layout, build Marlin 2.0.9.2 or later, or current bugfix-2.0.x, and use the MarlinUI configuration example, or otherwise enable #define DWIN_MARLINUI_LANDSCAPE.Additional Parts RequiredM3 6mm screw x 3(optional) M3 8mm screw, M3...

Both the Y and Z motors should be rotated in the case of Ender 3 Standard (please refer to the position of the motors connectors, as indicated in the attached pictures).In the case of Standard Ender 3, there will be a 10mm gap between the case and...

The following changes have been made: 1- Spaces for M3 nuts have been added in the underbody so that you can screw the board with M3 screws 2- Spaces for M3 nuts have been added in the upper part to be able to screw the two covers without problems...

Printed this case with my new Ender 3 V3 KE for his older brother, the Ender 3 V2.Just because the V2 was running on PLA, the model is perfectly printable on the V2, although the finish with PETG on a V2 is harder to master (at least for me)The case...

-Ender 3 power supply fan case cover for Arctic F9 92mm x 25mm Fan. https://www.amazon.com/dp/B08PZJ1ZL5?ref=nb_sb_ss_w_as-reorder-t1_ypp_rep_k0_1_9&amp&crid=189TG6PMZ0ZTM&amp&sprefix=arctic+f9 -I also added screw pads for a LM2596 buck...

In my case, I placed mine at the front right of the base, near the lcd of my ender 3 v2. I printed the case with the opening for the switch faced down to the bed and the opening for the back plate at the top. Supports from build plate are also...