ender 3 cable chain 3d models

This is a cable chain mounting bracket designed for use with the Ender 3 carriage, ensuring wires remain in place without chafing or movement. It secures to the carriage via two screws, providing stability through zip ties that keep wires rigid. Use...

... and the **cableChain_link_v3** to design a mount top that lets the cable chain run alongside the printer. ...The goal is to create a cable chain holder on the extruder, ensuring the cable runs straight and doesn't bend at the extruder level.

I liked the way the cable chain fit from the base to the extruder, but i didn't want the chain to the hotend.Remixed the extruder mount to work with Creality Filament Runout Sensor Bracket.

Update: March 22, 2020 - I tweaked the z-cable chain alignment (extruder_mount_5.4) for better performance. To shave off some extra weight, I remixed the cable chain link. ... March 3, 2020 - I added an X-axis mount, which weighs about 4 grams when...

A redesign of the Ender 3 v2 attachment for bed and Z chains by wku_wake. This design utilizes the hardware from the z stop mount after adding a bed level like the BL Touch.</p> <h3>Print Settings</h3> <p><strong>Rafts:</strong></p> <p>No</p> <p...

https://www.thingiverse.com/thing:4609298 https://www.thingiverse.com/thing:4785189 This print uses the cable links from johnniewhiskey, I used the cable chain connector (under the printer) from this (https://www.thingiverse.com/thing:4609298) file...

The cable chain used is available on Amazon, offered in adjustable sizes that can be easily customized: https://smile.amazon.com/gp/product/B07SFFT1K5/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 I will update this post once the other side of...

... Here is the link to the amazon cable chain i used. It comes apart in any size. ...https://smile.amazon.com/gp/product/B07SFFT1K5/ref=ppx_yo_dt_b_asin_title_o04_s00?ie=UTF8&psc=1 I will update the post when i get the other side done for the hot end

Additional Hardware required!I bought this cable chain (Amazon):https://www.amazon.de/dp/B0859BQSQW/ref=cm_sw_r_apan_glc_i_B8XNFC8FBQN778B8AE2E?_encoding=UTF8&amp;psc=1You'll only need 15 Links for this specific mod, I will upload an other version...

This modified version of the hotend side chain link mount boasts enhanced durability. I tweaked the original design to address its weakness where it gripped the carriage, which often led to breakage. Thicken this critical area and you'll end up with...

To complement my existing johnniewhiskey set, I discovered that some Ender 3 Cable Chain adapters required modifications to accommodate the cubic frame of my Ender 5 printer. ...Consequently, I created a custom adapter to securely hold the Z-Axis cable...

This is a modified version extruder mount from Ender 3 S1 Cable Chain by TechRex.Things I modified:Patched up the holes in the model.Moved the chain mounting point so the chain can stay straight with the Y-axis Mount.Print Settings:0.2mm layer...

I found the Drag chain/Solid cable chains are a significant improvement over the standard "ender 3 cable chains".Download actual chain files here: https://www.thingiverse.com/thing:371500Installation of these chains is a bit more involved, but well...

Remixed parts for Ender 3 V2 cable chain. Made extruder chain bracket slide into filament guide and use one of the extruder screws for attachment. The filament guide uses only one of the Z axis screws and the chain bracket is designed to slide into...

This is a remix: https://www.thingiverse.com/thing:3769941 With these 3 pieces you will have your cable chain complete and well aligned. ...

Remixed this thang because the X End cover was too small.

Remix of the Rear Mount from https://www.thingiverse.com/thing:2920060 Combined mount with v slot covers here: https://www.thingiverse.com/thing:4460641 If I get some time, I may repost with lengthened covers that extend under z axis motor.

Filled in the holes to allow them to snap into the extruder mount. ...You'll need supports, you can decide which direction you think is best, but if you print it with the pegs pointed down, keep the supports away from the pegs, they'll just pull right...

A quick and dirty remix to make this work better if you're using the MicroSwiss direct drive.

I used the design by FedorSosnin for the parts that connect to the printer, but reverse-engineered the parts that attach to the cable chain based on the components I received from Wish. ***Important Note*** The parts have been fitted and tested,...

https://www.thingiverse.com/thing:4314829 For the X & Y axis, I'm using the bed cable mount mount from WiredEarp, along with the hotbed mount and his loose chains. I tried MANY different chains, on different print settings, and they all bind up...

I tried to find the original here on Printables but I couldn't find it, so posting here so the Prusa-peferrers can find it too!This is an awesome cable chain that clips directly on to the Ender3/Ender3Pro's extruder and body rails without having to...

If you're struggling with a short ribbon cable for your X and E motors that can't be routed inside the chain along with the hotend cable, then this piece was specifically designed for you. Installation Notes ------------------ • Insert this part...

I managed to cobble together a hasty combination of the small cable chain and a different extruder/printhead mount (unfortunately, I couldn't locate it anymore - there are just too many with the exact same design). The extruder mount requires...

I tried to find the original here on Printables but I couldn't find it, so posting here so the Prusa-peferrers can find it too!This is an awesome cable chain that clips directly on to the Ender3/Ender3Pro's extruder and body rails without having to...

I leave the design of 3 versions 1a - Without filament guide 2b - With filament guide 3c - With filament guide and perfect fit (The one I am using) Necessary material: First the chain Motor support (use this with the end on the side) also this...

Here are three versions of the design: * Version 1a: Without filament guide * Version 2b: With filament guide * Version 3c: With filament guide and perfect fit (the version I'm currently using) You'll need the following materials to build this...

... filament guide for this mount would get in the way and be misaligned with my extruder, so I removed it and decided to share it. ...The bottom chain link connector is for the normal cable chain size, and the other connector is for the slim chain link.

Roller Mount for Ender 3 (Currently in Testing Phase) ************************************* Fixed Object Not Sitting Flat ************************************* Printed with: 15% Infill Rate Top, Bottom, and Perimeter Layer Thickness Set to 3.3mm Each...

I wanted to create a rail mount that could redirect cables and wires towards the X-gantry, so I designed an oblique and 90-degree offset version of the original "cableChain_40MountTop_v2". ...These new files are intended for use on the side to guide...