ender 3 bl touch 3d models
761152 3d models found related to ender 3 bl touch.prusaprinters
Remixed the BL touch design so it'd sit closer to the nozzle. ...With this design the drag chains I installed on my printer don't run into the vertical bars. x-offset: -42.10 mm y-offset: -17.00 mm z-offset: (take this with a grain of salt and adjust...
thingiverse
Unfortunately, the screw on my BL touch had worn out too much to adjust the height of the measure tip. ... As a substitute for the original sensor, I used this clone from Aliexpress: http://bit.ly/2McIHrB The approximate offsets for the new sensor are...
thingiverse
Remixed the BL touch design so it'd sit closer to the nozzle. With this design the drag chains I installed on my printer don't run into the vertical bars. ... x-offset: -42.10 mm y-offset: -17.00 mm z-offset: (take this with a grain of salt and...
prusaprinters
Ender3 BL Touch Mount with M3 Hex Nuts (5.5mm A/F) held in, to use original screws included with the Touch the offsets should be aroundx=-40.5 Y=-6.5Printed In ABS
thingiverse
This adjustment ensures that your touch is aligned properly to prevent it from dangling precariously off the edge of the bed as it makes contact.
prusaprinters
Ender 3 BL Touch simplified and close to nozzle#define NOZZLE_TO_PROBE_OFFSET { -27, -9, -1.68 } https://www.printables.com/model/331865-ender-3-pro-fan-shroud
prusaprinters
This is a remix which adds a support arm needed as the original mounting area where the BL touch attaches is too flexible and easy to snap off. I needed this when i upgraded my Ender 3 V2 to a direct extruder and wanted to attach the BL Touch, and...
thingiverse
... and easy to snap off. ... I needed this when i upgraded my Ender 3 V2 to a direct extruder and wanted to attach the BL Touch, and the bracket that was on the original Ender V2 didnt fit the direct Extruder, which looks to be like the Ender 3 Pro.
thingiverse
Here's a straightforward mount for a BL Touch sensor on your stock Ender 3 hotend. I created this because existing mounts were a bit too flimsy for my liking. This one boasts a thicker design and features strategically placed cutouts on the backside...
thingiverse
I'm thrilled with the modified mount as it's incredibly robust, and a version featuring hex nuts is available to support BL Touch mounting. ...However, this particular configuration was too low for my MicroSwiss all-metal hotend, so I created this remix...
thingiverse
On your journey to make your Ender 3 go pro you may run into a clearance issue after installing a BL Touch. If you find that the motherboard cover will no longer fit after plugging everything in, these files may help you. To fix this I thought...
prusaprinters
Mounting Bracket for the Voron AfterBurner Extruder, I have added a fixed BLTouch Mount as the removable ones seem to be too flimsy for my liking. Spacers included for the BL Touch mount , I uses about 5mm worth. x_offset: 37 y_offset: 6 I have also...
thingiverse
Spacers included for the BL Touch mount , I uses about 5mm worth. x_offset: 37 y_offset: 6 I have also updated the mount to remove some unneeded features and added in a required hole for the newer Afterburner design. Fusion Files included as...
thingiverse
... visit the source at https://www.thingiverse.com/thing:3003725. ... The modifications I've made include: 1. Removing the "Cable holder" feature allows for open holes in the carriage. 2. Erasing the "Ender 3" signature streamlines the surface design.
grabcad
The BL touch set is now configured specifically for use on an Ender 3/5.
thingiverse
Simple yet effective bl-touch mount for creality ender 3 v2 (becouse one that came with bl-touch fits only ender 3 v1). No need for additional parts, nuts or screws. ...Works perfectly with original set of screws.
thingiverse
Simple but sturdy bl-touch mount (becouse one that came with bl-touch fits only ender 3v1)
thingiverse
Compact BL Touch mount for the Ender 3 V2 Initial version (my preference, unless you use the Creality firmware and don't want to update the offset): Offset X = -39, Y = -7 Version with correct offset for Creality firmware: Offset X = -45, Y = -20...
thingiverse
... датчика авто-уровня BL Touch. ... Не мешающее не чему! Обновлено: 15.01.2022 * Мод под вплавляемые гайки (M3 X D5.0 X L4.0) https://aliexpress.ru/item/4000232858343.html * Усиленная версия крепления BL-Touch https://aliexpress.ru/item/32832887426.html
thingiverse
Hope this helps someone who needs the bracket who already has the BL touch sensor. I think this may fit a CR10 V2/V3 as well, but not 100% This is my first item design, so please let me know it it works for you. ... If you find this useful, please...
thingiverse
This is remixed from https://www.thingiverse.com/thing:4762570 with a height of 29mm. ... With the origin part the nozzle was to far away also for Z correction (Ender 3 max). ... This part with a height a of 25.4 mm works perfect in my case.
thingiverse
Ender 3 V2 BL Touch mount, which mounts using the existing V Roller bolt plus an additional M3 bolt through the bottom of the carriage. If you wish to use the plotter attachment, the model is designed to require 3x M3x3mm heat-set inserts to...
thingiverse
Insert the nuts included with the BL-Touch and attach from the bottom of the mount with the stock screws. Zip-tie wiring to the strain relief bracket. ... Design is based of a model of the stock CR-10 hotend by Geoff Tayler on GrabCAD ...
thingiverse
Set the Z offset by flipping the power button or manually touching the probe gently to simulate it touching the bed. 2. Run G29 to do an autobed level probe and save the settings to EEPROM with M500. 3. Check that the printer is working correctly by...
thingiverse
In the original bl-touch software (download from the creality website) it is adjusted according to the distance between the Bl-Touch needle and the nozzle tip. When you make Auto home from the menu on your Ender3v2 printer, the Coordinates are as...
cults3d
I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.
thingiverse
I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket.
prusaprinters
I modified the part to fit the Ender 3 Pro with or without the BL-Touch Metal Bracket. Category: 3D Printer Parts
prusaprinters
BIQU H2 V2 direct drive extruder Ender 3 Max with BL touch mounting plate. ...I have managed to mount it fine but some of the holes are fraction of the millimeter off. X offset is cca 56mmY offset cca 7mmInspired...