ender 3 5015 fan 3d models

update: added version 5, same design just a cleanup and a lot more stiffer so higher speeds are possible with sonic pad update: added v6, i added an air-channel to suck the air from more below the extruder So you need a 4xM3 screws, 1xM3 nut,...

Enhanced Velocity Upgrade Kit for Model 5015, featuring a modified mounting system compatible with Petsfang air ducts.

Compact and lightweight Fan Duct for the Ender 3 V2 for 5015 Blower with BLTouch Mount. Just one piece. No support needed. Probe Offset: X-35 Y-8. Z should be around -2.2mm. You only need one M3 nut for the Fan Duct. Weight: aprox 40g with 3...

Additionally I made a version that fits a 5015 fan for better cooling.As this was made on the basis of the normal Ender 3 version it will fit both on the ender 3 v2 and the original ender 3/ender 3 pro. Thanks to markymarc for confirming the...

As this was made on the basis of the normal Ender 3 version it will fit both on the ender 3 v2 and the original ender 3/ender 3 pro. Thanks to markymarc for confirming the compatibility on his ender 3 pro. The 4010 version does not require any...

Compact and lightweight Fan Duct for the Ender 3 V2 for 5015 Blower with BLTouch Mount. Just one piece. No support needed.</p> <p>Probe Offset: X-35 Y-8. ...Z should be around -2.2mm. You only need one M3 nut for the Fan Duct. Weight: aprox 40g with 3...

Fan duct for Ender 3 S1 You need 5015 fan, 3 m3 8mm. ...12.11.2022 UPADATE 4020 FAN

This is a remix of the AYF fan shroud to fit the original Creality Spider hot end.

I like the design of "BreezeBlock fan shroud" done by CoffeeOutlaw and yet I still prefer the "Radial Fan Fang for Creality CR-10" done by jneilliii.So I modified the holder to fit the Fan Fang. You'll need:M3 6mm Bolts x 4M3 16mm Bolts x 4M3 20mm x...

Very rough remix I made for my Spider hot end, 5015 blower fan and BL Touch. ...Not perfect, but works amazingly.

This hotend assembly enables the use of a Noctua 4010 fan as for cooling the heat break and two Sunon 5015 blowers for part cooling. NOTE: ALL FANS LINKED BELOW ARE 12V, THE ENDER USES 24V! PLAN ACCORDINGLY AND EITHER STEP YOUR VOLTAGES DOWN OR RUN...

Remember, keep this part as light as possible, infill should only be 10%-15%, go with max 3 walls, if you can do 2 to keep to weight down. Update (04/03/2023): Added a version to fit a 4020 fan. ... Youtube Channel: https://www.youtube.com/@zeltroix...

When I upgraded my Ender-3 to direct drive I decided to buy an aluminum stepper mount, but it was too big to work with this Satsana Fan Duct. Using a little bit of magic I was able to make this work and here it is for anyone else who wants a fan duct...

Update: 14.12.2022 -Adjustment of the assembly (Angled V2 to V2.1) with the 5015 fan, which was causing problems with some fan brands. 18.08.2022 version V2 -Fan placed a little higher to lengthen the elbow and leave more space. -Bracket shape...

A collection of hotend mods for my Ender 3 V2.

... a stock hotend with the Creality hot end fix done and it shortened the z axis height. If you have one, this duct works to adapt it to the ender 3 but I did not see the value in it and tossed it in the trash after using it for about 3 months. ...

Requires 5 M3 nuts and bolts to assemble The BLTouch mount is rigidly fixed, with a hole reserved for its cable BLTouch Offset: X: -37 Y: -35 This mount uses NEMA 17 21mm-24mm stepper motors; for thicker ones, there's a version without the left...

... and a pressure clip that he designed. ...I also took a look at his creation, which is a bit more rough around the edges than the original, but it still manages to hold an 4020 fan in place with ease. ...Overall, I think you'll find it quite useful!

I've created a new mount for Ender 3 Titan Aero as there were no dual 5015 fans models. ###Current state Release. Airducts and fan mount may change, but they a good enough according to real tests. The main mount itself looks to be stable, but may...

This is an updated version of my popular fan duct for the stock Ender 3, designed specifically for a larger 5015 filament cooling fan. Here's a link to my original design: https://www.thingiverse.com/thing:4369859. Like my original version, this one...

This is a revised version of my fan duct design that incorporates a holder for a dial indicator. The original design can be found on Thingiverse at https://www.thingiverse.com/thing:4528533. The holder itself has an 8mm diameter. ...I am using an...

I remixed this fan duct for beauty I added the dragon Ender logo I hope you enjoy

This design works great for my Aquila and my Ender 3 V2 (and should work for other Ender 3 models). I ended up incorporating a Mini Me V4 style hotend cooler mount into the RHD Fan duct for MK3 Bondtech BMG Mosquito...

Uses a 5015 radial fan and mounts directly to the x-carriage plate of a Creality Ender-3 (and I believe other Creality printers such as the CR-10, Ender-5, etc.). AliExpress link for the extruder in the Mellow store: ...

This design works great for my Aquila and my Ender 3 V2 (and should work for other Ender 3 models).I ended up incorporating a Mini Me V4 style hotend cooler mount into the RHD Fan duct for MK3 Bondtech BMG Mosquito...

... MK3S+ fan duct you need. All 3 parts print without supports. The prusa duct has a built in support in the file you'll need to snap off. ABL mounts can be found here https://www.thingiverse.com/thing:3182917 Parts cooling fan is a 5015 blower.

... MK3S+ fan duct you need. All 3 parts print without supports. The prusa duct has a built in support in the file you'll need to snap off. ABL mounts can be found here https://www.thingiverse.com/thing:3182917 Parts cooling fan is a 5015 blower.

This duct is very useful for a lot of Creality printers. ...It's mais function is to be an "easy to install" adapter for 5015 fans. ...STEP file is included in need of small adjustments.

... The Trianglelab BMG extruder without light pancake stepper motor can be purchased at this link: https://ali.ski/tb4kn. Additionally, a 5015 fan with dual ball bearing is available for purchase at this link: https://ali.ski/OhJKFB.

Hi, I've been using this BantaMount re-design for quite a while and decided to share it with everyone else!Firstly I had to slightly redesign the basic mounting system to fit the Ender 3 Max by removing a part and adding two screw holes to the...