ender 2 pro v2 3d models

C270 Mount for Ender 2 Pro bed. I made this in Tinkercad so its not perfect but is functional. Printed at 0.2 Layer height, vertically with the c270 mount on the bed, it uses the least support material and prints nicer that way. You will need a...

I used a mount that The 300lb Gorilla designed for me to mount the fan along with the EZABL micro. To mount the fan on the left side, I drilled 1.5mm holes for the top holes and used M2 bolts. The duct mounted with 2 bolts with nuts on the bottom.The...

A very simple spool holder to reduce the overall footprint of the Ender 2 Pro even more. I did this to fit more printers on my table in my print farm. Find the base here https://www.thingiverse.com/thing:5469874. ... Feel free to use the base to make...

A very simple spool holder to reduce the overall footprint of the Ender 2 Pro even more. I did this to fit more printers on my table in my print farm. Find the base here https://www.thingiverse.com/thing:5469874. ... Feel free to use the base...

Ender 2 Pro has a front facing MicroSD slot. There are no bolts or holes that can be used to attach a SD adapter. This is simple design that should be fixed with double sided tape. It was designed to fit the most common microSD/SD Card readers /...

Firmware Marlin 2.0 only for creality ender 3 pro. To make the upgrade, just empty your sd card and drop the bin file inside. Then with your printer off, insert the sd card and turn it on and in less than a minute the marlin logo should appear in the...

The Ender 2 Pro has the micro SD card slot located at the front and there's nowhere to fit screws.This is just a simple design to hold the common SD card / MicroSC card adapter at the front, with the use ou double-sided tape.Tips: Print it with the...

The Ender 2 Pro has the micro SD card slot located at the front and there's nowhere to fit screws.This is just a simple design to hold the common SD card / MicroSC card adapter at the front, with the use ou double-sided tape.Tips: Print it with the...

A Raspberry Pi camera 1.3 arm for the Creality Ender 2 Pro that attaches to the cover of the X axis, so it follows the printing process always at the height of the nozzle. To install the case you have to unscrew the cover for the X axis, slide in...

I used Tinkercad to adapt a Tronxy Crux 1 spool holder (that I had previously modified) to a Creality Ender 2 Pro keyed type so I could run small spools on my Ender 2 Pro.  Most of the small holed spools are cheap filament or specialty filaments.  It...

Revised Duet WiFi Ender 3 Pro Case Design for Ethernet Compatibility To accommodate the Duet Ethernet module in The-Doc's existing duet wifi ender 3 pro case design, a few modifications are necessary. Upon importing the original Fusion file, it...

Hello, I have taken the habit of having a precise adjustment for the limit switch of the z axis of all my printers.I searched for one of the ender 2 pro, but I didn't find any, so I made my own design and now I share it.Use 1 M4 screw about 30mm long...

I've been looking for good Z Axis support for my Ender 2 PRO, but what I found was too loose fit or doesn't fit at all - so I made my own in the end. Printing details are the description, but I also attached STEP file so you can edit this fix as you...

Here are some options for adding a ‘face’ to your Ender 2 Pro. I'm not at all artistic so please consider remixing this to make it more adorable and less ‘I’m gonna murder you while you sleep'. You can print the backs (red) and the teeth (white) in...

**Update 2022-12-12:** I made a far better version of this thing, you can find it **[here](https://www.printables.com/model/338566-hotend-fan-duct-for-ender-2-pro)**. **Summary:** I was annoyed by the noise of the hotend fan. To mount a quieter...

This was designed for the Ender 2 Pro but may work on other models with the same spool holder.Slides over and clips around the spool holder arm. ... The tabs keep the holder from moving around when the cutters are removed and...

My Ender 2 Pro has the BTT SKR Mini E3 V3.0 and on that there is a dedicated neopixel header. There are also plenty of setup tutorials on youtube for getting the neopixels up and going. I think this will also fit Ender 3 and other similar style...

UPDATE: Version 2.0 is here: https://www.printables.com/model/382003-ender-2-pro-sd-card-adapter-and-wyzecam-v3-mount-v This is a mount I designed to add a Wyze Cam V3 to the Ender 2 Pro. There aren't very many good mount points on the printer...

My Design for Leveling the X axis Gantry on the Ender 3, Ender 3 Pro, Ender 3 V2

I had an old iPad 2 lying around and decided to mount it to my Ender 3 Pro as an Octoprint controller. I printed it on edge with supports for the right section. I was concerned about weight and balance so added v-slot extrusions on 3 sides. It also...

If you are printing this on an Ender-2 Pro, you will need to set the skirt loops to 0 to avoid going off the build plate. I used 100% infill, though, I am sure it would work just fine with less than that as the whole model is mostly walls. ...

I've been looking for good Z Axis support for my Ender 2 PRO, but what I found was too loose fit or doesn't fit at all - so I made my own in the end. Printing details are the description, but I also attached STEP file so you can edit this fix as you...

Rediseño de Manta https://www.thingiverse.com/thing:4403017 y https://www.printables.com/es/model/169185-manta-compact-fan-duct-tool-change-system de BoothyBoothy para mi Ender 3 pro, quería utilizar los ventiladores de fábrica y adaptar otro del...

I grabbed an old iPad 2 gathering dust and decided to mount it to my Ender 3 Pro as a controller for Octoprint. I printed it on edge with supports for the right section. I was worried about weight and balance so added v-slot extrusions on three...

CringeHead is a direct print head for Ender 2 Pro with RBS (remote blower system) airduct. You need to use K3D minifeeder (https://github.com/dmitry-sorkin/k3d-minifeeder) as a feeder for this printhead (nema14 + bmg gears). Heatsink - any...

Second generation of my hotend fan duct for Ender 2 Pro. **Advantages:** - better air flow, - 4010 and 4020 fans mountable, - good view of the nozzle, - sturdy, - easy printing, - easy assembly. Print with heat-resistant filament, PLA is...

This is a phone mount I designed for the Ender 2 Pro. It uses M3 nuts and bolts to attach firmly to the left side of the case and hooks onto the LCD panel for stability. All parts were designed to be printed without supports. The bolts in the...

The back panels slot in, though you might want to use a drop of crazy glue with light clamping pressure to secure it.If you are printing this on an Ender-2 Pro, you will need to set the skirt loops to 0 to avoid going off the build plate.I used 100%...

Updated Ender 3 V2 filament Guide 2.0

... This is a mix of two dust filter ideas: https://www.printables.com/model/262818-filament-dust-filter-for-ender-2-pro https://www.thingiverse.com/thing:190118 Print Settings Printer: Ender 2 Pro Rafts: No Supports: No Resolution: 0.1 mm Infill: 100%