enclosure for ender 5 plus 3d models

Ender 5 Plus bracket designed specifically for SKR 1.3 and 1.4 motherboards, optimized to provide easy access to the SD card slot and USB port. To assemble this bracket, you'll need to locate and carefully cut a precise slot and hole on one side of...

All parts are for the Creality Ender 5 Plus. The light strip can easily be stuck around the corners and you need less than 3 meters from the light stripes. Required parts: - 2 pieces AngleBar1 - 2 pieces AngleBar2 - 2 pieces...

This is a remix of the switch mount for the 3DChameleon MK2 that fits in the rear left corner of the Ender 5 Plus sitting ontop of the corner bracket allowing for you to use the Y axis to trigger the switch. The switch ends up triggering at the same...

List of parts: - Platsa struture 503.309.46 - Värd glass door 603.473.19 - Smastad doors 204.342.38 - Hjälpa shelf 903.311.66 - Lätthet legs 203.311.98 - Hjälpa hinges (x6) 603.312.00 - thing:4090325 (https://www.thingiverse.com/thing:4090325)...

... ...Useful for cleaning the glass bed with alcohol after each print. Print Settings Printer Brand: Creality Printer: Ender 5 Rafts: No Supports: No Resolution: 0.16 Infill: 12% Filament: Additive Heroes PLA Black Category: 3D Printer Accessories

This is a simple strain relief for the print head cables on the Ender 5 or Ender 5 Plus. It just snaps on and adds some cable ties to secure everything in place. For the latest updates on this project and others, join my community at...

Creality Ender 5 Plus 2020 2040 Cable Covers Will suit any 2020 / 2040 sections (This was 100% infill) All parts are thin and weak but with care they work well. Remove using a paint scraper under the edge near the clips and twist carefully. Creality...

If you own an Ender 5 Plus and install the Printermods MDD 1.2 direct drive plate, you'll discover that the stock metal BLTouch mounting plate won't fit properly. None of the pre-printed BLTouch mounts match, so I chose to modify the metal one...

My ender 5 plus factory spec out the box has this additional dampening bracket. Which needs slightly more space for the cover to fit properly. Test prints fit perfectly. Use the same fastening / fixtures listed in the original. ...Worked a treat.

Extended lower and upper corners to fit Ender 3v2.Printed with PLAPrint: 0,2 mm layer height, 0,4 mm nozzle, 40% infill. ...Supports only on the lower corners on the 90° overhang.</p>

# WHAT THIS 3D PRINT IS NEEDED FOR AND WHY IT WAS DEVELOPED: This 3D print resulted from the fact that after a while the cable guide of my Ender 5 plus kept bending towards the heatbed due to the weight. After a while, the cable guide was so deep...

I'm Sick of Long Bowden Tubes and Backordered Hemeras, So I Designed a Direct Drive Mount for My Ender 5 Plus. I'd had it with the lengthy Bowden tube that always seemed to be in my way. Then, when I was ready to upgrade to a Hemera, it went out of...

Use the same information as the original file, this just adds a slot to store one additional SD card on the side From original: So I made this thing for my Ender 5 Plus +, you need a couple of M3 or M4 x 10 bolts and T-nuts to attach it. I also put a...

Using the BondTech BMG/V6/Volcano direct drive for Creality Printers by Hangtight on MyMiniFactory with the Ender 5 Plus can lead to a problem where the BLtouch doesn't trigger before the nozzle hits the bed. The BLtouch adapter screws in exactly...

======== This mount allows the use of the direct drive quick change toolhead by VORON Designs called the Afterburner on a Creality Ender 5/Pro/Plus. The Afterburner is the latest toolhead from Voron and offers the flexibility to use three different...

This remix is for using a BTT Octopus on a standard Ender 3. I also found that my printer varied from the 3D models on Creality's github, so I made some changes to make it fit my actual printer. You do need some T-nuts to install this, but you may be...

This enclosure remixes two Thingiverse Designs: 1: Kilroy01’s Ender-5 Control Panel Back Cover https://www.thingiverse.com/thing:3353394 2: Wolfganghsu’s Snap-on LCD Cover for Creality Ender-3/Ender-3s/Ender-3 Pro/Ender-5...

I'm using it on the new SKR 3 board for the Ender 5 Plus, but the SKR 3 mounting points are the same as the SKR 2, and I think the SKR 1.x boards too. I printed this in ABS, but PLA or other material should work fine. It's designed to be a press...

... mounting boss at the front, and tweaked the cover. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 0.2 Infill: 10% Filament: Printed Solid Uncle Jessie PLA Safety Orange Category: 3D Printer Accessories

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ...Will Need: 10mm Magnets 3mm...

Wanted to test out HexOrt inspired wobble wings on the ender 5 plus to see if it would help with layers lines. After about 2 months of testing, I can say they have significantly reduced layers lines on most of my prints. ... Will Need: 10mm Magnets ...

The Ender 5 plus's location on this design smacks the Bl touch on the Z rails when homing, moving it out of the way but still requiring offset changes to avoid hitting the left-hand side Z rods. ...I adjusted these offsets in the starting gcode within...

This will adapt the stock screen mounting to a BTT Pi TFT 43 4.3" Raspberry Pi Touchscreen on the Ender 5 Plus. I run Klipper with Kliperscreen and it works flawlessly. Adapter brackets center and hold the screen where it needs to be. Gives a...

Ender 5 Plus bed cable support. Wanted one which was simple, solid and didn't require additional parts. To install just remove the two screws on the bed frame, slide the support in and reinsert the screws. ...The screws don't touch the support, they...

However, the following text has been rewritten: The Enders 5 Plus bed is connected to a cable that keeps it safe. ...To secure the cable, just snap it into place in the square hole and tie it up with some cable ties, just like you see in this picture.

Im Rahmen meines Ender 5 Plus Umbauprojektes, musste ein Adapter für die neue SKR 1.4 Turbo Platine. Der Adapter hat noch eine Halterung für die SD Verlängerung von Creality. Für die Montage werden, 3 M3x8 Senk, 4 M3x16 Zylinder und 4 M3x6...

See the original creator here: https://www.printables.com/model/436006-ender-5-plus-with-microswiss-ng-cable-chain The original creator made these for a 10x15 cable chain that was purchased from Amazon. He used the closed version of the chain,...

To attach the raiser to the frame of the Ender 5 Plus you can simply use M3, M4 or M5 T-Nuts. You can get them here: ...

This print is for side mounted light bars for the Ender 5 Plus. I wanted them on the sides so they were out of my way and have two light bars for better lighting. The brackets are RH / LH so the X axis motor on the gantry is the RH bracket. I also...

This includes two lengths of bracket designed to move the standard spool holder bracket 25 mm or 50 mm rearward on the Ender 5 Plus. This allows for the use of large replacement spool holders such as the design this is a partial remix of. The newly...