enclosure for ender 5 plus 3d models

After Experiencing Disappointment with Several Brackets, I Decided to Create My Own Using Fusion 360 Primarily to Enhance Y-Axis Stability on the Ender 5, but It May Also Suit Other Printers and Applications Utilizing 2020 Style Extrusions Such as...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.

this is a mount to attach the Mosquito hot-end to the Ender 5 plus carriage. ... it will work with my Satsana duct remix found here https://www.thingiverse.com/thing:5120862 Please let me know if you want any tweaks or changes.

I wanted to attach my Ender 5 Plus to my IKEA Lack table cart. I made these, so I didn't have to drill through the printer frame and the top of the Lack table. ...I used these clips: https://www.thingiverse.com/thing:4091348

Ender 5 Plus motherboard fan bracket. Use 4 self-tapping screws to attach the holder. It is possible to use two cheap 12V fans connected in series and connect them directly to the motherboard at the 24V output. ...Use 8 M3x14mm screws to attach the fans...

These are a remake of the stock corner brackets that come on the Ender 5 Plus. I made these as a temporary replacement. ...They will not work on the Top Back corners unfortunately without moving the location of the end stop.</p> Category: 3D Printer...

A slightly modified belt tensioner body to fit on the Ender 5 Plus X axis carriage. ... It still requires the nut and thread part of https://www.thingiverse.com/thing:3601830 and this spacer to fit the stock bearings with an M5 bolt:...

I created these inner channel clips to keep your Ender 5 plus cables hidden, neat and tidy within the frame. There are two sizes you can use (small & big), it depends on how many cables are in the channel, you'll use the small or big one. Print it...

This is a remix of zarify mount https://www.thingiverse.com/thing:4087221 but made to fit an Ender 5 Plus It wont quite clear the hot end but does a good job and doesn't require and additional hardware. ... the cover is friction fit and you may need...

... housing that comes with the Ender 5-Plus. This can probably work on other creality machines that use the same filament sensor housing/microswitch as the Ender 5-Plus You might need to hot glue the PTFE tube to the housing so it doesn't move around

I used the E3D Volcano mount to attach the Spider to the Ender 5 Plus. This allows you to position the Spider at the same z height as the stock hotend. You mount it upside down from the pics in the link:...

Does the world need another extruder knob for the Ender 5 plus? The answer is yes, if you use Micro Swiss' direct extruder along with the cable strain relief from Sergentchat https://www.thingiverse.com/thing:4591387 (scale it down to 10 %). ...

Introducing my alternative solution for upgrading the hotend of the Ender 5 Plus, incorporating the Spider Hotend from Creality along with dual 40x40x10 fans.This upgraded version boasts dual fans, an additional fixation point at the rear,...

This designed seemed the best for my setup on an Ender 5 Plus. ...So remixed it to attach onto the rear 2040 extrusion Uses 4 M5 x 10 bolts with tnuts to attach to the frame. Print Settings Printer Brand: Creality Printer: Ender 5Rafts: No Supports: ...

Here is my Ender 5 Plus MeanWell PSU cover. The 60mm fan is placed so it uses the stock fan vent under the printer and using a 60mm fan bought from RS components (RS Stock No: - 696-3544) is almost silent compared to the standard fan. This will...

...Just use support blockers everywhere else. This will fit an Ender 5 Plus. It has a hole in the back for the drive belt on the hot-end. You may need to adjust your X limit switch slightly to prevent it from crashing when it homing. Good Luck! ...

This is a remix of the Y axis MGN12H linear rail mount for the Ender 5 plus that drops the linear rail to the bottom V slot of the 20X40 extrusion. Y axis end stops are included as this drops the height of the X axis back to around the stock height...

The jetpack has been halved and will fit on an Ender 5 Plus bed and print without supports. To put the halves together I have added dowels and pocket screws. I've also put in some screw holes at the back and adapted the way the rockets are fitted so...

---------------------------------------------- This is an adaptation of my unpublished Ender 5 Duet Mount, modified for the Ender 5 Plus. It utilizes a 40mm fan (recommended: 24v SUNON 4020 or 12v Noctua 4020 via a buck converter) to direct air...

Remix of Ender 3 - Filament Holder Deluxe (https://www.thingiverse.com/thing:3114139) for Ender 5 Plus (tried to upload it as remix, but Thingiverse is not able to find the original design) - I was happy with the original design that I have used on...

I needed a filament guide when I upgraded my Ender 5 Plus to direct drive. With this I could have the filament spool sitting the same place as before. This is mounted instead of the old extruder. Hardware required: 2 x M3 Bolt 2 x M3 Nuts M6...

This is a bracket for the Ender 5 Plus controller case to move the cooling fan from the bottom to the rear of the controller case and cover the fan's old hole. The air will now be pulled in the front sides and exhausted out the back. The bracket...

VIDEO: https://www.youtube.com/watch?v=RpIH-jXLHm8 ENDER 5 PLUS: https://bit.ly/2YHzpws BMG: clon:...

This adapter simplifies installation of the Mean Well RSP-500-24 power supply unit into your Ender 5 Plus significantly. You will need (8) M4 x 8mm button head screws and (4) M4 nuts to complete the process.\r\n\r\nInstallation note: Extending some...

This a no extra / different screws required print to mount your Big Tree Tech touch screen to your ender 5 plus. Both objects are all in one file. It includes the mount and adapter. ...Some clean up will be required depending on how your printer is set...

This is a filament lead in tube (Bowden) end holder for Ender 5 Plus direct extrusion modifications. It is designed to hold the end of the filament lead in tube from the filament break detector to the direct extruder. The filament bracket installs in...

Aluminum LED Channel brackets for the Ender 5/ Plus printers. You will need to print two of each file for all four needed. The brackets do not have holes for the wiring, but 10 seconds and a drill bit will put the hole wherever you want it. Used...

Simple yet effective replacement for your Ender 5 Plus duct fan. Exhaust is directed under a small angle, now featuring rails, so airflow points directly at the nozzle tip. I hope you'll be satisfied with the results. If any issues or tips arise,...

Decided to go another route, but if I had kept it I would've reprinted in PETG.Printed great on my Ender 5 Plus, I added 3 perimeters(for a total of 6) and 10% infill(for a total of 25%) for some added strength.Print SettingsPrinter...

This is a housing for the Mini 12864 LCD display to fit inside the Ender 5 Plus chassis without modifications.It bolts on from inside using the original mounting points and screws.You mount the LCD to the back cover first with the M4 screws and nuts,...