enclosure for ender 5 plus 3d models

Will need some sanding and epoxy. ... Epoxy the Air Director to the Air Director Cover. The "tall" version can be used to keep the wires off the bed (Ender 5 Plus)

This bed wire strain relief device mounts directly to the 2020 extrusion that forms the Ender 5 Plus's bed support, securing itself with M5 bolts and 2020 T-nuts without needing to disassemble the bed or any other components.

Remix TFT70 case that mounts over the hole of the stock screen on a Ender 5 Plus. Two clips center it and hold it in place. ...I used (4) 2.5x6 screws to hold the clips in place.

Remixed an ender 5 plus fan duct to fit on my fan. ...The previous one had some extra plastic on that the screws go through and didn't fit on mine.

I made a housing to fit the BTT mixing 2in1out extruder that can be mounted on the Ender 5/plus backplate. The hous is made for 2 40x40x10 fans on the extruder cold end an is directing the air up away from the buildplate. I also remixed the layer fan...

Precision Leveling System for Ender 5 Plus. Using the standard M4 screw, this Leveling System allows z-adjustment of 0,05mm per step. This version is desined to fit a ISO nut M4. If there is intrest, i will upload the adjusting wheel with the hole...

A simple wire support for your Ender 5 Plus hotplate should fit others just as well. Secure it with cable ties under the hotplate mount right next to the bed leveling screw. The first test print was made with HIPS, extruder temperature at 240C, and...

Extended Trays for Ender 5 Plus Machines Require Original Parts from Thingiverse Link To build these extended trays, you'll still need to obtain original parts from the following link: https://www.thingiverse.com/thing:4116655. Key Changes to Note:...

I wanted an LED strip light for my Ender 5 Plus, but all I found was this one for the standard Ender 5: https://www.thingiverse.com/thing:4125317 Front and rear lighting is nice, but it wasn't wide enough for the Plus so I needed something bigger. At...

EN: I have developed a dual nozzle conversion for the Ender 5 Plus or for all printers with the usual roller guide system. The original mounting plate was modified and re-milled from aluminum. I tested it with a PETG prototype before milling, and it...

Dan's tutorial and parts can be found here: https://e3d-online.dozuki.com/Guide/Hemera+Creality+Ender+3+(CR-10)+Upgrade./107?lang=en For my Hemera conversion, I utilized the stock Ender 5 Plus Thermistor, Heater, and Fans and purchased a longer...

The official Creality all-metal extruder upgrade (Pictured) sits slightly wider than the standard plastic Ender 5 Plus extruder, causing the filament exiting from the filament runout sensor to misalign with the new metal extruder. I created a...

This is my first post on Thingiverse, I wanted to add more color to my Ender 5 Plus so I re-created the corner brackets to be printed in any color you wanted. I did a 20% infill, Layer Height of 0.2, wall thickness of 0.8 and did use supports for...

This is my version of LED strip support for ENDER 5 PLUS. Is to be print with support , back on print plate. there is a left, and right part, but they are quiet similar, so maybe no matter if you print only one piece twice. You will need : 16...

hello this is my modded led light bar holder for my ender 5 plus but will fit others on the main bracket i used 50% infill and on the led holder i used 100% infill this is to fit the led which was from amazon this is the link...

I recently purchased a new extruder gear for my Ender 5 Plus. It's a knock off Bondtech Geared extruder, but works well. However the new gears put the filament path about 9mm higher than stock. I designed a simple spacer to accommodate the increased...

The way I have my Ender 5 Plus set up, a cable sleeve just dangles loosely and frequently scrapes against the printer's frame. This is the first modification I've made to the printer. I printed the part with 40% infill, 100mm/s speed, .2mm layer...

This is a magnetic snap-on case for the BTT TFT24 display to attach to a Ender-5 Plus printer equipped with a BTT SKR v1.3 or v1.4 board. Four magnets are holding the case onto the existing LCD cutout. Magnets: 4 pcs 10mm diameter and 2mm...

I designed this to replace the boring black limit switch covers on my Ender 5 Plus with no additional hardware needed. They will also work on limit switches on other Creality machines, but you will need two M3x14 screws. I have test printed this...

... stop. ...I was having issues printing on the 5 plus and discovered that the PLASTIC corner braces were cracked. I replaced them all with machined aluminum and the printer is now very rigid. ...I made a remix of the ender 3 bracket for the limit stop.

I wanted a sleek light bar for my Ender 5 Plus, but every standard LED strip didn't fit, so I grabbed xqqqqme's clips and gave them a makeover to match LilTrublMakr's bar perfectly. I removed the v-slot modification and here's what I came up with -...

Since I'm not using the stock Ender 5 plus display, I've remixed a BTT TFT35 mount with a 40mm fan grille. Just an easy no case modification required to add another cooling fan to the case. ...Should fit any 40mm fan, screws for fan mount are M3 length...

quick and easy guide for the ender 5 plus hotend loom. Needs 2x 3mm T-nuts to mount to the back rail. I used PETG but I'm sure PLA would be fine. Just make sure the hole is smoothed out (some nibs from z-seam might want rubbing down) so the harness...

This is almost the same size as the stock Ender 5 Plus holder, maybe 2 mm shorter. It works on the Ender 5 Plus, and the Ender 3 v2. It should work with other models as well, but I have not tested it. You will need two 608 bearings. ...You can use...

Bretware Ender 5 PLUS Chain System Please subscribe to our Youtube channel https://www.youtube.com/channel/UC-dZpDgCGSf7w-vZWgO2Nsg/videos Uses Johnniewhiskey Ender 3 chain To be used with the following, Chain and covers...

You may locate the crossbar at any height you find suitable for your setup.Also consider printing the End Covers that protects you from the sharp edges that get exposed when you relocate the crossbar:...

Fits on you microswiss direct drive for ender 5 and ender 5 plus.You'll need to fiddle with the bowden tube and cut it down a bit.It sits on top of the stepper motor, I glued it down with hot glue. ...Have yet to see if it holds.I'll take more pics when...

Update 8/9/2020 ----------------- The original case bottom design has been renamed "Ender 5 Plus Case Bottom - Creality Mosfet" to indicate it's designed for mounting a Creality Mosfet board. A new version of the case bottom and top have been...

This is an Adapter that allows the installation of a BTT Octopus 1.1 (and also 1.0) and the Stock MOSFET that comes with the Printer into the case of the Ender 5 Plus. ... If you want to be able to access all of the Ports of the Octopus, you need to cut...

Modification for adding linear rail on the x-axis on an Ender 5 Plus. Printed in tool steel, optimised for low weight. The parts will absolutely not be stiff enough if printed in plastic. The brackets needs to be printed in two sets, and bearing...