enclosure for ender 5 plus 3d models

This endoscope mount has been modified to fit Ender 5 and Ender 5 Plus printers with the same front fan shroud as Creality. The mount doesn't obstruct airflow or interfere with the fan, allowing for smooth air circulation through the printer. It...

Modified based on https://www.thingiverse.com/thing:4795205 for the Ender-5 Plus * Changes some of the screw points * Moved one of them to allow for a Ground Wire * Added clamp system for the Ender-5 Plus control box All credit goes to the original...

Ender 5 Plus run out sensor bracket for dual drive extruder (BMG type).Bracket places run out sensor at correct offset for use with dual drive extruder like the BMG.Adds filament guide.Link to Ender 5 Plus firmware config and cable management photos....

This is a bracket for the Ender 5 Plus to hold the Meanwell 600W SE-600-24 in the Ender 5 plus's stock housing. This can be done with slight lengthening to some power wires. ...There are two stl's attatched, one designed to be drilled for 4mm inserts...

Chain mounts and bl touch mount for ender 5 plus + microswiss direct drive After adding the Hero Me Gen5 to my ender 5 plus I didn't have a bracket that fit my bl touch and I wanted cable chains so I made mounts for them.

I printed this clever component for upgrading my Ender 5 Plus to the Bigtreetech SKR 1.4 and a Raspberry Pi: https://www.thingiverse.com/thing:4328907 Unfortunately, the Mosfet of my Ender 5 Plus has a slightly unique configuration. ...That's why I...

... to 100%. A 100mm clearance behind the Creality Ender 5 Plus is required for this setup. For a more compact design, check out the short version without the arm here. Spool Holder Cones: The perfect solution for effortless filament spool rotation.

For users seeking a simple yet reliable solution, this dust cleaner offers seamless compatibility with the Ender 5 Plus and other compatible printers that utilize 1.75mm filament diameter. To ensure optimal performance, attach it directly to the...

Ender 5 Plus Z-axis supports. Has slots (for flexibility) for M5 screws with a counter-bore for flush mounting. ... The bearing used is a 608, in this case a ZZ as I had them already.

... use this method. There is also a Short version without the arm here. Spool Holder Cones for filament spool turninghttps://www.thingiverse.com/thing:3461608 YouTube Creality Ender 5 Plus View Spoo Videohttps://www.youtube.com/watch?v=EA1Udq_S97E  

Remixed from another design that would interfere with the carriage endstop on Ender 5 Plus. ...This one has been modified to fit properly and is working perfectly on my Ender 5 Plus.

Adapter bracket for an SKR 2. ... Made for Ender 5 Plus, could fit others. I used a SKR 2 but should fit 1.4, 1.3 also. ... Has wire tie down points at the bottom.

The electronics changes include: TH3D Parts: * EZboard Lite: https://www.th3dstudio.com/product/ezboard-lite/ * Dual Z Stepper Motor Adapter with Cable: https://www.th3dstudio.com/product/dual-z-stepper-motor-adapter-w-cable/ * Heated Bed MOSFET:...

With this 3 d print you keep your cabels of the Ender 5 plus neatly in place.

lilttle foot to raise something up by about 10mm. ... I have 4 of them installed under my ender 5 plus. ...

Just a mount to attach a Noir camera to my ender 5 plus. ...Printed laying flat with no supports.

Just a mount to attach a Noir camera to my ender 5 plus. ...Printed laying flat with no supports.

This is a remix of the original to fit over the BLtouch that comes standard with the Ender 5 Plus.

Filament tube guide for the stock extruder setup on an Ender 5 plus. This support angles the tube at 10 degrees towards the bed. ... Hardware: 2) M3x16 screws 2) M3 t-Nuts

I'm implementing a Simple Patch for the Ender 5 Plus Filament Sensor. ...The Problem is that it's registering a False Empty Reading whenever the sensor gets nudged aside by the filament.

Here's a custom foot I designed for the Ender 5 Plus, printed with Cura Slicer. ... If you find this helpful, consider donating an amount you deem fair via PayPal to help offset my time spent on the design.

Ender 5 plus 2.3kg spool holder. Works with 0.75kg and 2.3kg spools. 50mm Diameter 105mm Width Mirror 3DS1 for dual setup. ... Works with the original hardware from the standard spool holder (one in each holder)

This is an Adapter for the tubing of the Polybox to connect properly with the Ender 5 Plus. ... This is A Remix of the of the Design by Doloth https://www.thingiverse.com/thing:4249749

LED Bart bracket for Ender 5, Ender 5 Pro, Ender 5 Plus etc. This bracket will fit to 2020 aluminum. LED size which I used is width 13.3mm and thickness 8mm. Please feel free to comment for another sizes! I really appreciate your likes, makes,...

LED Bart bracket for Ender 5, Ender 5 Pro, Ender 5 Plus etc. This bracket will fit to 2020 aluminum. LED size which I used is width 13.3mm and thickness 8mm. Please feel free to comment for another sizes! I really appreciate your likes, makes,...

This is an STL of the MicroSwiss Direct Drive Extruder plate for the Creality Ender 5 Plus. The STL was provided by MicroSwiss. ... I highly suggest buying it from them:...

... and end over the motor to mount standard 15mm x 15mm drag chain. ... It fits my ender 5 plus but will work for the ender 5 aswell. ... I used the chain trays from https://www.thingiverse.com/thing:4164988 It was printed in PETG and 30% infill.

This is enclosure for [Mellow FLY TFT V1 3.5 inches](https://aliexpress.com/item/1005004091787313.html). ...The enclosure was designed for Ender 3 printer.

... Y Axis Tensioner. ... Also recommend to print this belt Guide, while youre on it. https://www.thingiverse.com/thing:3968980 This is a Remix of files you need for Ender 5 + to make a Belt tensioner. ... You have all the parts you need from the printer.

Ender 5 Upgrade to Ender 5 Plus Offers Enhanced Features and Improved Performance. The Latest Version of This Popular 3D Printer Boasts a Number of Notable Upgrades, Including a Larger Build Volume and a More Efficient Extruder System. ...These...