enclosure anycubic vyper 3d models

A simple 3D printed mining rig mobo chassis/frame intended for open-air or custom enclosure PC builds developed into a multiple GPU mining rig frame. ONGOING WORK!!! Versions: v.1.0 Initial design. 7" HDMI TouchScreen bracket, power button...

The emergency stop gets mounted on the outside of your enclosure box and routed back to the GRBL pins. Now you are ready to assemble the laser! The laser goes into the laser heat sink, which goes in the cooling duct. The duct blast shield gets...

but dont do that unless you have an enclosure and can get up past 110C... Alternatively using alligator clips and an oven would probably be more effective... just don't go too hot... 110C for an hour is probably enough. I have also added a sheet of...

Note there are small rings to support the holes when printing, these should be removed before inserting bolts from the flat side of the hangers.Slide the hangers into the holders, depending on printing tolerances the hangers may be very tight, but...

Using an enclosure to ensure a successful print is HIGHLY recommended. If you want one but don't want to put the time into the setup, buying the filament, and printing one successfully, I may be able to help print them for you--just make a request in...

It's called OpenHead not only because it is fully open-source, but also because it incorporates open structure without any enclosures (unlike the stock T2 head, which is enclosed cube), providing you easy access for tuning and maintenance. The main...

Just make sure they are suitable for dish washer use, so they can handle the temperature. *4 self cutting screws (the two delivered with the device are fine, but the case is prepared for four screws and you need slightly longer ones to secure the...

This is an enclosure for a Waveform / Signal Generator built with an Arduino Pro Mini or Nano (ATmega 168 is sufficient) and an AD9833 Programmable Waveform Generator. One 18650 Battery can be fitted inside the case together with charging and...

In the attached data sets, you will also find the circuit diagram and the Arduino code as well as the enclosure as an STL file. All parts can be bought on the Internet on eBay. Below is a rough listing of the parts required. 1x USB Cable 1x...

6x #4x12mm screws (for Nano enclosure and control box lid). 2x 3mm bolts, ~ 15-20mm long (for motor). 1x M6 bolt (for camera mount) 1x M6 threaded rod. In terms of weight capability, the main factor is probably the acrylic panels and plastic rather...

A dedicated enclosure for your Impos.... I... I mean PC, to keep protected from dust and the occasional kick when you are playing spin the chair. The Table top has dedicated slots for fixing your office necessities so that they are easily accessible....

1.2Runtime counter placed to keep track of the working hours/on-time of the Laser. The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20This box will fit in the enclosures made by Stepcraft.Hardware:DS...

So I made this self-sufficient planter enclosure with a sleek aesthetic so my succulent could live in the same space I do.The Nesting planter snaps out nicely with press-fit magnets, which also holds an optional integrated drip-tray. The LED...

Measuring 348 cm high and 245 cm wide, it provides ample coverage for users to relax and unwind within a carefully selected shade sail's protective enclosure. With a total weight of only 1.85 Kg, handling this compact piece of equipment poses no...

on the top frame rail right side rotated 90deg so the filament still spools off with the least bends (how I wanted to mount mine and the reason for the changes) On the top of a enclosure or flat surface with either screws, the joining plates to...

## Print Details **Printer:** My trusty Creality Ender 3 Pro, equipped with a glass bed, insulated enclosure, and "blue" bed springs for optimal performance and longer screws for added durability. **Filament:** I used high-quality Geetech(Sunlu)...

Note that in my four months of printing and testing, this has not introduced any heat related PINDA sensor "sag", even while printing ABS and PETG in an enclosure.\r\nAdded a slight teardrop shape to the main filament path directly above the bondtech...

At first I was thinking about printing the entire enclosure. That´s why the source file includes a filament ring like the ones included with the dryer, just without the tray area. However, even so my printer can handle the size, it would be a...

... also made a little PCB for the ESP8266 and some other components. This PCB is just something I quickly put together. I will design a better PCB and associated enclosure later and also link it in here. ...For now, you can find the PCB I'm using here.

This video explain the problem for the big enclosure extractor fan and the small MC Fan. https://www.youtube.com/watch?v=3M76VUJzwqY (I don't recommend to replace the big fan by his alternate 12v fan and his step down regulator because an rpm error...

The Heavy-Duty Air-Tight Filament Spool Case is designed to enclose a single standard 200mm spool in an air-tight enclosure. The standard design allows for 65mm wide spools with a 50mm centre. You can alter this by adding or removing layers and...

Printing at an ambient of < 70F seems to exasperate this effect as well as having a breeze present over the buildpiece (window, fan, air duct ...) To avoid these issues you can do a number of things: Make sure your buildplate is free of oils...

http://www.thingiverse.com/apps/customizer/run?thing_id=49590 Instructions Using the following options: back_port2_position = 0 left_port5_side = top back_port1 = none right_port4 = none right_port4_side = top front_port1_custom_circle_radius = 0...

The other side has 5,5 mm through holes, so you can use a threaded M5 rod to stack them my way if you like to. In this case you need 2x 135 mm + 2x 120 mm M5 threaded rod (you can use 4x 135 mm) and 4x M5 nut. I've added 2 versions of spacers to...

Printing in PLA is probably OK, even in an enclosure, but PETG is suggested.Additional HardwareM2.5x5mm screws, qty 4, for mounting the RPi. My stupid butt grabbed the wrong box of screws and used M3.</li><li>M3x10mm screws, qty 4, for mounting the...

If you are printing in ABS on a standard filament extrusion printer such as the Creality Series of printers (Ender 3, Ender 5, CR10, etc.) - make sure that you print your parts in an enclosure or heat tent such as the tent sold by Creality For it's...

I have done the work for you.The original gantry PCB is replaced with the "auxiliary" PCB, and the "breakout" PCB is located inside of the main electronics enclosure at the bottom of the printer. The original ribbon cables (unique to the CR10 Smart...

Klipper), dual-motor Z-axis upgrade, silicone pads replacing the bed leveling springs, an enclosure, plus a red racing stripe and a highly-aerodynamic spoiler at the rear to make it go super fastNozzle:0.6mm brassMaterial: eSun PLA+ in my favorite...

I also wouldn't recommend putting the control board under the Lack Table enclosure - it's a nightmare to work on. Here's a video of it in operation: https://www.youtube.com/watch?v=PN6U2HKLrDY I'm planning to design a less bulky part cooling duct...

The v-core arms used are from https://www.thingiverse.com/thing:5131325 by MFBS and has a https://creativecommons.org/licenses/by-sa/3.0/c licenseThe VenterMech is from...