enclosure anycubic vyper 3d models

**Note:** Detailed description with more photos here: https://github.com/Halytskyi/SmartThings/tree/master/3d-printing/ANYCUBIC-Mega-Pro I found [tutorial how create enclosure based on Ikea Lack...

This is an enclosure for Anycubic I3 Mega 3D printer. It's based on "Square Tube Connectors / Joints + Plexiglass support" that you can find here: https://www.thingiverse.com/thing:2927377. I added two supports, a and b, to help place the enclosure...

2 6mm x 455mm rods 1 6mm x 388mm rod 6 8x3mm magnets (I use four more to close the enclosure) I've used a large trash bag and duct tape to create the enclosure, with the front panel separate for now since I don't have transparent plastic. You can try...

This is a custom clip engineered specifically for the Anycubic Predator 3D printer. The design enables you to seamlessly attach a cardboard or pearl board shield directly to the printer, effectively separating it from external temperature...

Here is my version of the Predator enclosure front door, i am using Carstens rear panel mount design for a full enclosure. The bushings need to be printed in TPU. The door i have tested pla and petg with good results. BL=bottom left TL =top left MLB=...

<p><strong>Hello,</strong></p><p>this is a small upgrade that the z-axis is holding in the z-axis guide without Wobbling.<br>its easy to print and you can you how good your printer is calibrated :-D</p><p>make it first over the Bearing and than in...

This a small upgrade that can help you avoid filament detector problems. ...Easy mounted without any screws and glue.

Remixed arm for 1/4" screw hole for cameras. Check the original thingiverse for the mount and pin. ...Might make a horizonal version later on.

Resized model.

<p>Remix of model “V6Adapter-3mmShorter_1.stl” from thing#4976966.&nbsp;</p><p>The original file would become loose over time and permit the hot end to turn creating a z-wobble like banding pattern. I added holes for 2 m3x16 screws and 2 m3 nuts. The...

Lampholder for dual 5015 Printhead.

UPDATE: I separated the pin and the back part. I also redesigned the back part a bit, so it won't fall off easily. ---- Because I was annoyed with the need to use cable ties each time for holding the printhead-cable in place (and i ran out of...

Schutzkappen für die beiden oberen Ecken der Z-Achsen. Schutz vor Staub und Beschädigung. Gedruckt mit TPU, aber andere Materialien sollten auch passen. Der Entwurf ist so gestaltet, dass es locker sitzt. Automatic translation into English ...

- 10% infill, you may want to increase this for the slider if you want it to block more screen lights.- I used tree support for the case - Recommend to use 0.2mm resolution

i don't know much about 3d design but i tried my best to make this because the other ones i found either didn't fit right or the grip was too loose or so tight it squished the tube. ... my sensor still lights up when the printer goes to the far...

M3 inserts and 4x M3x16 cylinder screws are required.

modified from the original to have cut sections where the zip ties are placed to be able to cinch down further. ... 0.2mm layer 25% infill 40mm/sec 225oC / 65oC brim 3mm

Filamentchange at 0,6mm ruthex M3S Gewindeeinsatz SHORT -... ...https://www.amazon.de/dp/B09MTRHBRL?ref=ppx_pop_mob_ap_share

Hi this is my first Thing ;-) So have grace with me... ... It is an Camer holder for the Raspberry Pi it can move in all directions Instruction: You need to glue Part 2 and 3 thogeter (may change in future) And for the rest Flathead Screws 4x M4...

Inspiration from others on this space, I've designed these to hold the filament sensor in place, plus additionally keeping the cables from touching the build plate knocking off my prints. ...

Replace the noisy PSU fan with a noctua 80x25mm fan. Will require 4 M3x20mm bolts Its a 12V system, just need to cut and connect wiring how ever you like. ... Side cover is very thin to reuse the original hardware, can make it thicker and use any...

# If you Made it, # # Put your Photo on "Makes" section. # ## Italiano: ## Coperchio per i v-slot telaio della stamapante. Incastro facile sia dentro che fuori. Puoi utilizzare lo slicer per impostare una lunghezza, per esempio io li ho...

Klammer für das Kabel und den Bowdenzug

Here's a simple spool support I created in Fusion 360. I didn't like how the spool holder would twist and sag, causing the filament reel to slide over and look like it would fall off. The support is easy to install and remove and keeps the spool...

Hallo, hier mein Entwurf zum einbau eine Noctua 80x80x25 Lüfter 12 Volt mit Stepp Down Ich habe es noch nicht selber gedruckt aber es sollte passen. Benütigt wird: 1x 80x80x25 Lüfter (Noctua 12 Volt) 1x Stepp Down 24 auf 12 Volt 4x M3x16...

I know it looks flimsy, but once it's tightened up it's solid in case you are wondering what phone mount I have on there https://www.thingiverse.com/thing:2368959

- 10% infill, you may want to increase this if you'd like the slider cover to block more lights - I used tree support for the case

Customized version of https://www.thingiverse.com/thing:2615842 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2615842

This is an improvement version of @taka0909 and already asked him for the credit. There may be some problems in the original designs like the arm is not strong enough and the part is a bit conflict with the lower platform. Also, to make it easier...

Un petit support pour metttre un rpi qui heberge octoprint ou astroprint. ... Passe juste sous le plateau, donc ca prends pas de place !