elsa 3d model

I first encountered the idea for this type of robot in a biomedical article, presented as a potential new candidate for exploring the human colon due to its simplicity and ability to navigate confined areas....

This model is for a “streetlight-style” wired garden/pathway light. Brighten up your garden path with lights, without spending a fortune on MoonRays or similar products where a single lamp can cost up to $20! In bulk I can make these for about $3-5 a...

My O scale model train layout represents the section of the Pittsburgh & Lake Erie Railroad between McKees Rocks and Youngstown. This wall section (stretcher bond brick pattern) will let you assemble a background flat of the McKees Rocks...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_top_outer_edge_chamfer_radius = .6 stencil_vertical_position = 40 use_mouse_ears = 0 custom_back_camera_x_size = 20...

And get your supports in order first, the models need a relatively precise and flat supported surfaces. <font size="3">The modification uses many parts from the original setup, but the PTFE tube must be cut, making this a non-reversable mod...

I RECOMMEND THIS ONE INSTEAD:https://www.printables.com/model/169138-prusa-mini-detachable-cooling-duct-assembly-v2 About this modI have never been happy (okay that's a lie, I was happy for the first few weeks) with my Prusa Mini's cooling. This is...

(The toothbrush still shouldn't fall out, but a hole any larger and it might...)(I also use a print of the original model as a holder for fine detail paintbrushes, so a hole in the bottom of that one would be rather pointless.)Enjoy!Print...

[Medium Sized Model - 25mm base] [Presupported in 32mm and 75mm scale]   The strong silent type of the Spirit Samurai. Kaoru is often thought of as the defacto leader of the group, despite being one of the youngest and much to the annoyance of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

I've seen some Hedron models before, but none of them were quite right to me - they got the patterns wrong or just looked off in some way. So I set out to design my own, and this is the final result. Well, these are the final results because there...

If you need to use a different pump you can model and print your own adapter as it is just a rectangle block with a hole for the pump water outlet. The inlet block should be 80mm tall and 32mm wide minus half a millimeter for fit tolerance. If you...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 stencil_horizontal_position = 50 custom_back_camera_x_position = 0 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_left_port_y_position = 0 custom_top_port_x_position = -10 use_stencil = 0 pattern_line_thickness = 32 stencil_pattern_element_shape = 4...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

PLA will end up sagging, and failing over time.All of these parts are oriented in the correct printing position aside from re-centering the models.No supports are needed. *The cable chain end links printed fine with NO SUPPORT in all 30 different...

Existing models didn't meet my needs, so I created a parametric part. The current parameters are tuned for use with an M6 thread and prior tapping. I recommend printing a test part (produced by setting debug = true) to ensure your tolerances are...

The build and schematics can be found at: https://www.printables.com/model/282166-runtime-counter-v-20 This box will fit in the enclosures made by Stepcraft. Hardware: DS 15 connector female (signal out) DS 15 connector male (signal in) Mono...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_right_port_y_position = 0 custom_top_port_corner_radius = 5 custom_left_port_length = 50 pattern_element_rotation = 45...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

I always use a 4-5mm brim around such big models. You may need to turn off the skirt line then.</p><p>The 8 holders inside were printed with 100% infill, just to be sure that they were stable enough. You will need some screws, washers and nuts as...

DesignThis is the reduced to the max case / housing / sleeve for the Raspberry Pi Zero (2 W) in the version with cooling (we have another model that is prepared without cooling), less is hard to imagine. A foldable print in place housing with live...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_case_wall_thickness = 1.6 custom_back_camera_corner_resolution = 8 custom_left_port_corner_resolution = 8 custom_corner_resolution = 8...

**Update October 26, 2017:** Since I was messing around with the model anyway, I figured it was time to do something I've wanted to do for a while. To decrease the "stack height" on top of my inexpensive flexy tripod, I slapped an 18.5mm ball clamp...

Note: these videos are uploading slowly, so they might not be fully processed when I publish this model. They should be available in a few minutes.</p><figure class="media"><oembed...

For any other question, please feel free to reach out, or leave a comment. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: .2mm Infill: 20% Filament: Jarees PETG Matte Black Notes: Support is only...

* Test your work again * replace the toothpick with the mounting pins * improve the models and share your changes with the rest of us! The difference between this and the original is that I have add a version of the body which has an opening...

I usually split such models on 2 or 3 parts that are easier for printing. Then these parts can be glued as a one piece (with acetone for ABS, or dichloroethane for PLA). So other version of parts I am uploading is prepared in this way. My black...

The model isn't geometrically perfect as I did the scaling in blender (The only editor I know how to use), but it works which to me is the most important thing. You will need a couple screws to put it together as the ones which come with the...

They are both definitely WIP, I do not own a Orbiter V2 and are based on the CAD models. Update:18\10\21 Uploaded some 5010 fan ducts which are 8.5mm longer to allow for a Volcano Hot End. These are definitely WIP. I have not printed, installed or...