elephant knife 3d models
35380 3d models found related to elephant knife.
prusaprinters
The following are some precautions I took to ensure good first layer adhesion and avoiding warping. Print one file at a time to minimize time on print bedFreshly clean your print bed with soapy waterAdjusted elephants foot compensation (in Prusa...
thingiverse
* For "advanced": * Elephant foot compensation: 0.2 (if you don't have it set already). After printing, carefully remove supports. If there's a stubborn layer or two of supports on the very bottom of the case, that's OK, it won't interfere with...
cults3d
Print the effector, make sure the cross shaped opening in the centre is clean of any brim or elephants foot-first layer, attach it to your printer. The only difference is the upper part has the nut traps on the other side. Attach the circular...
prusaprinters
This results in increased "elephant foot" on the outside of the print, which you usually try not to do, but shoving that foot further out will make the interior wall flush on a vase mode print. This flat inner surface is just what you want for a...
prusaprinters
I used a white led strip but an individually addressable RGB led strip is going to be fitted and I will update the guide once it's finished.Materials need:chipboard (2 cm thick enough to cut out 2 circles with a diameter of 500 mm) or one sheet of 4...
cults3d
What I was blaming myself for as elephant feet wasn't as the holes were misaligned by .1 of a mm. Much easier to screw things in from the bottom of the plates now. Added a motor mount that was offset by 7.5mm(half the distance between holes of the...
prusaprinters
Snap piece BM into the printed cradle.If the piece is warped slightly, you can use the heated bed to heat up the piece and hold it flat for half a minute to make it flat again.Once the piece is seated nicely and flat inside the cradle, resume the...
prusaprinters
Some parts might not fit on smaller sized beds.Rafts:NoSupports:NoResolution:0.2mmInfill:15-20%Filament: PETG/PLA Additional notes:2 perimetersColor change (Base, Side (Left-Right)): >2mm and >5mm (2.2mm and 5.2mm in Slicer)Avoid using XY...
prusaprinters
table_mount If you only want to print a vertical piece, or half an arch, etc.: end_cap Print settings: Supports: NONE (!!!) Nozzle size: .4mm Elephant foot compensation: 0.2 Brim: Exterior/Diffuser/Base: Disabled (0mm) There is a built in brim...
prusaprinters
Double-sided Textured PEI Powder-coated Spring Steel Sheet before printing with PETG filament.For thin parts to stick correctly, you may need to adjust height of first layer perfectly and to reduce "Elephant foot compensation" from default value...
cgtrader
Name: Light_Bridge_Leader\nVersion: Alpha_11\nPreview: Enabled_by_Default\nUnits: Metric_Measures\nDimension: Five_Foot_Nine_inches_by_Eighteen_Inches_by_Three_Hundred_SevenpointSixFive\nGeometric_Parts:...
thingiverse
Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a...
thingiverse
Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a href="https://www.thingiverse.com/thing:3837220"...
thingiverse
Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a...
thingiverse
Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a...
thingiverse
Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a...
thingiverse
Print with nut insert" /> Electronics Tools • Accessories Hand Tools Power Tools • Accessories <a...
thingiverse
... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">
thingiverse
... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">
thingiverse
... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
... alt="" width="123" height="92" /></a> <a title="Cap.Am. Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank">
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...
thingiverse
Wall Decor" href="https://www.thingiverse.com/thing:5195100" target="_blank"> ...