elegoo saturn vat 3d models

Elegoo Saturn 3 Ultra Build Plate Draining Arm This model is designed with screw mounting bits, the build plate is reliably fixed, the size of the hand screw is M10*25, using standard M10 nuts, it is recommended to use 20% fill for printing, I used...

It helps to reduce amount of resin on the build plate after printing and prevents of excess resin fall off both the platform and print itself.Could be printed on Mars 4 Ultra itself directly on the build plate without any supports.It is designed by...

Um ein Wham Bam Flexible Build System mit einem Elegoo Saturn (2021) zu verwenden. Die originalen M3x6 Befestigungsschrauben, habe ich durch M3x8 ersetzt, da die Originalen mir sonst zu kurz gewesen wären. Wham Bam empfiehlt einen Abstand von...

This simple component can be used to level out the height so that the controller can be operated properly.I glued the adapter to the Elegoo Saturn with double-sided adhesive tape and then glued the controller to the adapter. With the right adhesive...

This is a handy build plate holder for a Elegoo Saturn 3 Ultra. It can help you to pour off a lot of resin after printing. ...By my measurements, your economy will be about 5-15g per one printing.Here you can visit my other projects, hope, you enjoy...

original text: https://www.thingiverse.com/thing:4867200 adaptator / corner to place the Elegoo Saturn platform on a anycubic wash & cure plus there 2 designs for each level inside the wash and cure My text: I have remixed the parts that do not have...

This is an adapter for the PTC heater that fits on the top of the Elegoo Saturn with the top that measures 104mm X 55mm X 7mm in XYZ respectively. I had found one on here bit it was too small for my top for some reason. This model includes a wire...

Designed for 4 inch dryer hoses. Currently only contains STLs for the Elegoo Saturn, but the OpenSCAD files can be easily updated with measurements of other printers. Still a WIP, intending to update the design to not require supports, as well as be...

A simple fume vent system for your Elegoo Saturn and Mars 3D resin printer.ELEGOO Saturn 4/3/2 and Mars 5UPDATE 03/07/2024 -  Elegoo Technical R&D Personnel have confirmed for me via e-mail on the 03/07/2024 that all the Saturn and Mars Series UV...

The bottom of the Elegoo Saturn has an intake vent, so the rear fan/vent areas can be vented. This should help with fumes as well as UV light cooling. This remix allows the vent to print without any supports. The taller top area also allows more...

The build plate drip attachment is compact and avoids touching the VAT below it, so there's no need to remove it.

Remix of wildcardfox's Saturn vent duct adapter to work with 4" ducting instead of 6" 6mmx2mm magnet holes added for attachment or just tape it on. ... Tested and works well on my machine.

Confirmed to work on the mars 2 pro and saturn. Should work on anything with a 22.5mm hole. printed with Siraya Tech Tenacious. ...I don't see why it can't be printed with tpu

I was annoyed about setting up vat to the right position with my hands. ...So I made up this little upgrade that holds Air purifier and keeps the resin vat on right position.

Remix of the MakerMatrix's design (adding the half-round cutout to allow the build plate to go the full way onto the Saturn's arm). Only modified the "2021" variant with holes for resin printing. The only difference is the cutout for the build...

I noticed that on my Saturn 2 the port on the back did not line up to 70mm or 75mm so I am not sure if they had an unusual size or the process making these warped the holes a bit. either way, measured mine and found this fits but be certain to try...

I noticed that on my Saturn 2 the port on the back did not line up to 70mm or 75mm so I am not sure if they had an unusual size or the process making these warped the holes a bit. either way, measured mine and found this fits but be certain to try...

6pcs M3 x 12mm cap head bolts (securing the Cover_Interface_V2_LG_FDM_v2.stl to the Elegoo Saturn 2 resin printer) 2. 9 pcs.[Tapered Heat-Set Inserts for Plastic, M4 x 0.70 mm Thread Size, 4.700 mm McMaster-Carr...

Mods for the saturn 2 Here you can find the code for the arduino to control the pwm fan and read the thermistor. ... https://github.com/kondrez/Saturn-2-UV-light-cooling List of used parts for the frontpanel: -W1209 Temperature controller (Celcius...

These parts make it easy to connect and disconnect a 3" vent hose to the exhaust port on the back of the Saturn 2. I didn't want to have to lift the cover with the hose attached, so this was my solution. I believe someone else has made their own...

Took the components around this popular resin heater build and designed a solution that is mounted to the 75mm ventilation hole found in the saturn 2 and saturn 8k covers.  The heater is mounted via a quick release system to let you remove and add it...

Heater controller temperature probe is mounted near center front in the wall of riser to read the temperature of the resin vat, not hot air blowing from the heaters.Front center thermometer is measuring the temperature bottom middle at the screen...

I think works with PETG

Un coperchio per serbatoio di resina in modo da non doverla svuotare sempre.

ATTN: Not tested Yet. (Will upload photos after printing) The day I got the delivery of my resin (MSLA) printer. After homing I tried to raise the print bed but due to the processing delay I tapped too many times. This caused the bed assembly to...

This is a remix from https://www.thingiverse.com/thing:398515 As I had problems printing it in 2 parts since it was pretty close to the edge, barely fitting, I split it in 4 parts which you can join with glue.

Magnetic rear vent filter. Can cut your own carbon filters to fit the vents. Designed to use a combination of 5mm x 5mm round magnets as well as 25mm x 8mm x 2mm rectangular magnets but can get away with using just one of the two types. ...

A simple bucket to prevent any resin from leaking thourgh the Cable slot inside the printer and ruining you motherboard and UV light. The bucket is fixed on 3 existing threaded holes, use 3x M3x5 to mount the bucket. ...Becarefull not to use longer...

Remixed funnel holder for large paper paint strainer Category: 3D Printer Accessories