elegoo saturn flexplate 3d models

3 part heater bracket for Elegoo Saturn. The simplified design is based on: https://www.thingiverse.com/thing:3442165 and https://www.thingiverse.com/thing:4737945 with the aim of being easy to print on FDM I used the same hardware as...

The Elegoo Saturn is an awesome MSLA 3D printer, except that I really like the cover I have on my Epax X1 which was a hinged cover that flipped up to open. I designed a "Hinged  Cover" that uses two gas struts to help smooth out the cover opening...

A bracket that snap fits on the back exhaust port of the Saturn V1 to help mitigate the fumes from the resin.

If you needed a riser for an Elegoo Saturn 2 this project has you covered.  It included a step file of the dimensions of the cover rim, step and stl files of a 25mm tall riser, and a link to the project where you can modify it for free using...

Höhenverstellbarer Abtropfständer passend für Saturn 2 mit passendem Alu-Profil 20x20, Schraubern M4x25, Mutter M4 Das Holzbrett hab ich bei IKEA in der Resteecke günstig bekommen. ... Ich stelle euch auch gerne die DWG-Dateien für Änderungen zur...

This is a drip jig for the Elegoo Saturn 3 Ultra. It’s basically a remix of other drip jigs for so many of the other resin printers. Not sure who came up with the original ideal for this type of design, but kudos to whoever it was. I wanted a jig...

This is a remix of @DaveK's remix of Cryptothornton design to make it fit better the Saturn 3 12K.I've shortened the arm that holds the build plate by approximately 10-12mm so that it doesn't go over the VAT edge and make a mess while the excess...

The holder of the building plate of the saturn varies according to the model, make sure yours is like the one seen in the photos, the one that is square. This holder allows two angles of inclination, both for the left and for the right. All in one...

If you have a flex build plate for Saturn 2 as i have then you might want to print this spacer that go's between the sensor finger and the saddle of the printer. ... the spacer is 3mm thick so you will have to use longer M3 Cap heads, I used longer cap...

... as one and sliced/printed the way I wanted. It is snug on the Saturn 2, but definitely fit as described in the original model and doesn't cause resin to drip past the vat. ... For resin printing, use one of the original models, not this remix.

There are two versions: 1: 2020 version - Earlier Saturns had a slightly thinner trapezoidal section on the build plate arm. 2: 2021 version - Saturns produced after ~late 2020 have a slightly thicker build plate arm. ... For each of the above...

I also lengthened the arm so that it hangs closer to the left side of the vat and I've lengthened the arm that the plate hangs from to center over the vat better.  Update, it has come to my attention that not all Saturn 2s are the same I’ve added 2...

There are three versions included, the Supported and Unsupported are designed for printing flat on the build plate of your Saturn. The supported version includes a thin resin support that is easily removed (instructions below).The FDM ready version...

Based on the dimensions of the Snapware container, you can fit a Saturn part into the container at the maximum build volume dimensions. I designed a part that sits firmly onto the magnetic stirrer and holds the container on the platform at an offset...

Adaptation of "Elegoo Saturn Build Plate Draining Arm by MakerMatrix" so it fits 2021 Elegoo Saturn.

Single Arm Elegoo Saturn 45 Build Plate Hanger

Elegoo Saturn 2 Vent Port for Flexible Duct 3 Inch

Elegoo Saturn S Z 2.6mm Offset WhamBam

Resin tank stand/holder for Elegoo Saturn 3 12k UltraPrint 2 pcs and assemble it

Elegoo Saturn S Z 2.6mm Offset WhamBam Use 8-10mm M3 screws

This is a WIP, still needs some testing. Each tooth from the bottom up is 62 ml of resin with the halfway point being 430 ml. I've tested that with my vat and water and seems to hold up. The max line on the tank indicates 500 ml. Sits pretty...

I wanted a vat drainer that stuck on to the build plate holder instead of having a separate contraption. This was printed with a mixture of: 75% Phrozen 4k Aqua gray, and 25% Siraya tech Tenacious. ... it is a rather tight fit so the tenacious really...

Simples levelers to put your 3D printer at the correct tilt. ...

Based on the dimensions seen at https://www.youtube.com/watch?v=D3LI2_m00Uk. ... I've used it once and it worked great.

Impression sans supports Follow Me Here : Youtube : https://www.youtube.com/c/BODY3D Facebook : https://www.facebook.com/B0DY3D TikTok : https://www.tiktok.com/@body_3d Team BODY3D : https://www.facebook.com/groups/492474174608397/ Instagram :...

I made this cover to protect the VAT/FEP. ... Hope you all like it

Impression sans supports Follow Me Here : Youtube : https://www.youtube.com/c/BODY3D Facebook : https://www.facebook.com/B0DY3D TikTok : https://www.tiktok.com/@body_3d Team BODY3D : https://www.facebook.com/groups/492474174608397/ Instagram...

Just a basic handle

This is a WIP, still needs some testing. Each tooth from the bottom up is 62 ml of resin with the halfway point being 430 ml. I've tested that with my vat and water and seems to hold up. The max line on the tank indicates 500 ml. Sits pretty snug...

The object is used to position the satmpa plane at a 45 ° angle to allow the residual resin to flow into the tank and be recovered