elegoo saturn fep 3d models

Magnetic mount for your vent hose so you can easily attach/remove when you need to lift the top off. ... uses 6.35mm magnets and has holes to press in brass embedment nuts Print 2, one for the hose side and one to mount on the printer

Tilted and angled mount that stays on and drips resin into the VAT. ...4-40 hardware, 3mm might fit as well.

This is a remix of the original riser to make it printable on smaller build plates. All 4 parts are held together with M3 6mm (4x) screws. Should fit nicely to your SLA printer. ... You need to print 4 parts: - front left (FL) - front right (FR) ...

Remix to add an angle so the resin runs to one side.

Customized version of https://www.thingiverse.com/thing:21112 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=21112

Une pièce pour permettre au plateau de la Elegoo Saturn 3 Ultra de s'égoutter correctement dans le bac à résine. C'est la pièce qui permet de le faire sur la Elegoo Mars 2 qui m'a servi de modèle.N'hésitez pas a faire en sorte qu'elle ne casse pas,...

HARRY NEEDED AN FEP FINGERNAIL

FEP screws organizer, an accessory to leave your work table organized for FEP replacement, without losing screws and tools.

I wanted a mount for the Wash basket, so I could just plonk the build plate in the alcohol, without needing to hook other things on. Knocked up in TinkerCAD, Printed in PLA+, 0.6mm width, 0.2mm layer and 20% infil. No idea if it will end up...

Redesigned heater system here: https://www.thingiverse.com/thing:6403707Top plate for the heater and fan is direct replacement for stock z tower plate. Printed in PETG for temperature resistance.Riser is printed in 4 corners to fit 200mm print bed,...

Modeled up a quick spacer that is the thickness of the Wham Bam XTR magnet and 1 Flex plate. ...  This seems to be completely optional for this printer, but offers piece of mind that if you build plate was gonna smash into your screen it wasn't due to...

Der Anschluss wurde für ein 50mm Rohr adaptiert. Im Anschlussstück ist ein 80mm 12V PC-Lüfter verbaut um die Dämpfe in den nicht genutzten Schornstein zu entsorgen. Danke für die Super Idee von pizzaparker! ...

Slightly tweaked the original file by chopping off the ends a bit. ...The original sat flush against the rails and I needed mine to have a bit more space.

<h4>Print 8 of these clips (or more) to attach a fermentation belt to your at.</h4><p>I recommend using some kind of plastic that handles heat well, so plan jane PLA might not be the best choice. ...Picture is ASA filament.&nbsp;<br><br>Fermentation...

Remix of https://www.thingiverse.com/thing:5334643 for increased height at 3.8mm for Wham Bam XTR

Increased the size of the cut-out where the vat retainer screw hole sits to allow a bit more leeway should you still have the screw inserted when draining the vat.

From the original by MakerMaveric "simple holder that also blocks the lid from being put on completely (so you know you forgot something), as well as uses the stock screw on the right side panel. I hope I'm not the only idiot that needs something...

Logo removed using Autodesk Inventor Professional 2022.

Update 1/16/24: Printed in ABS-like resin and the housings are holding well so far. The temperature in front of the heater is reaching about 70C with fans on.Added modified housings models.Update 1/8/24: After about 5hour print the heater cases...

The build plate drip attachment is compact and avoids touching the VAT below it, so there's no need to remove it.

___ You just have to perforate adequately the FEP following the procedure and you'll have any FEP brand ready like a tailored LD006 FEP. *Even if perforation is harder, keep both FEP plastic protection during this process.* ___ Easy peasy FEP...

a printable disk to help tensioning the FEP vat foil for a Photon S

Fep between two plates, press down, put on vat.. ... NOT TESTED

A technician is tasked with installing a seal around the FEP vat to minimize air pressure fluctuations.

I made a tiny FEP tuner, just place this under your FEP film while tuning to get the right tightness of your film. ...The tuner has a height of 13mm wich gives your FEP the perfect slack before tuning.

... it. While I'm not sure how much it truly impacts FEP performance, I notice that the FEP is more uniformly pressed onto the glass before filling the vat. ...This might also help with resin levels and flow back by taking up space in the vat.

This was the original, really. ...It's a non-slotted version of the FEP scraper/spatula/putty knife I use. ...Some people may want the extra body for scraping build plates like a 500lb gorilla :)

A quick mockup of an idea to help install FEP sheets on an LD002h/2r This is not tested - so print and use at your own discretion. Press the FEP sheet down between the two plates, and hold over the vat to start the screw down process. ... I got the...

This is a replacement to the proprietary FEP frame Anycubic is trying to sell for their M3. Print two of the same .stl. The indents are mirrored so it fits into itself. You install it similarly to the way the old frames worked using a bottle cap.