elegoo neptune upgrade 3d models

... knob from turning while printing. ...Fits the Neptune 4 Max. ...I assume it will also fit the 4 Plus since they have a similar design.For X axis on 4 MAX/Plus use the X axis stopper from original project: https://www.thingiverse.com/thing:6130503

I created this mainboard cover to be able to use a 80mm fan to cool the board and to reduce the noise of the fan used on my Neptune 2S. ... Because the printer will be higher you need to print new feet, I printed these ones : ...

Elegoo sent me these STL files for a dual z drive setup. ...If you get the creality dual z drive kit I don't believe you will need the wheel bracket.

I added a BLTouch mount to Tal's Neptune 3 Fan shroud, this enables greater flexibility in hotend choice and significantly speeds up bed leveling. I also shortened the duct slightly as the original version had the duct very close to silicone sock and...

I will add the other Neptune printers if someone provides measurements.Another Tip to save frustration. If you install the Z rails make sure the X-axis is square to the upper frame before tightening the X to Z rail bolts. I did this by simply...

Loved this design from Code Monkey Zero, however unfortunately it isn't compatible with the Neptune 2's stock BL Touch mount on the X axis carriage - I've added a mounting plate that is as close as possible to the original stock BL touch mount points...

Decided to make my own Tray/Nozzle Holder for the Neptune 2S. Holds the 4 included nozzles, the 2 bowden tube holders, and the Extra clips. When printing I added extra support to the end of the narrow section to help with adhesion, you may...

I wanted a basic, straight-on webcam mount for my Neptune 2D (similar to the ones I had printed for my Ender 3v2 and Voxelab Aquila), so I remixed both https://www.thingiverse.com/thing:4914473 and https://www.thingiverse.com/thing:4781893 to come up...

Designed a Storage (drawer) for tools for the Neptune 2 and Printed it on it. It fits in the Bothe sides of the Printer. Maybe it fits into the Ender V3 if its the same 40x40 aluminum profile. If you this helps and want to encourage my...

The desired voltage output should be measured at ~12VDC.Disassembly:Remove the (6) hex screws securing the rear access panel, then disconnect the (2) power wires from the LED driver module and set the panel aside. Disconnect the 2-pin fan connection...

Created a Cam Mount to fit my Logitech C270 Cam on my Neptune 4 Plus. I like too monitor my print so this print is made so spot directly at the nozzle. You can tilt the cam so only nozzle is visible and a lot of the print.Does fit to the right side...

I wanted a basic, straight-on webcam mount for my Neptune 2D (similar to the ones I had printed for my Ender 3v2 and Voxelab Aquila), so I remixed both https://www.thingiverse.com/thing:4914473 and https://www.thingiverse.com/thing:4781893 to come up...

Moin, ich hab mir die in der black week 2,3 kg Rollen von Redline Filament bestellt und musste feststellen, das die gar nicht auf den originalen Filamentroller vom Elegoo 4 max pro passen :D, daher hier mein angepasster Filamentroller für bis zu 30cm...

| Stock : Direct axial loads to the Z stepper | This holder : Reduces loads to the Z stepper | | ---- | ---- | |  |...

... change. The Elegoo magnetic display mount attaches to this one with the same 3 screws it came with. The camera holder is from https://than.gs/m/751499. ... The original display holder is from https://www.thingiverse.com/thing:5765043

This is a Remix from Neptune2 Elegoo Non display side tray from Fabius_Bile I have removed some unecessary stuff like the hiden storage its a good model but I decided to remove that and also one of the wall to get more access to the SD card slot.

I wanted to clean up the Z-axis wires on my Neptune 2S, they've touched the table and lead screw during a print before. This cable cover has a nice pressure fit, but also the filament detector screws can be used to fasten it. I use it together with a...

It slots nicely onto the right hand side right next to the x-axis belt tensioner.There is a cable guide for the wires that will go to whatever you're using to take the photos (I'm using a Raspberry Pi 3b).To use the time-lapse feature, use the Elegoo...

I've created my own implementation of the following cables clip design:https://www.printables.com/model/722500-enhanced-anti-drag-cable-holder-clip-for-elegoo-neMain differences:Can be printed without supports;Cables are fixed in place so you do not...

Da der Boardkühler des Neptune 2 sehr laut ist, hab ich diese Abdeckung designed, um einen 80x80x25mm Lüfter direkt über das Board platzieren zu können. Um die Abdeckung nutzen zu können, muss der Drucker mindestens 30mm höher gelegt werden. Dazu hab...

After deciding that the original cable clip that came with my Neptune 4 Max was designed by a sadist, I decided to create my own. This one is designed to hold the cable flat and out to where it doesn't rub on anything and also keeps it from block the...

... XYZ Steps/mm to get perfect results. Also you should Upgrade the Part-cooling with a dual 5015 design. also I recommend getting a TRIANGLE LAB 3D Touch or BL Touch or CR Touch. No cheap no name clones! Trianglelab clones are good though. ...

 ## Compatible printers I confirmed this working on ELEGOO Neptune 2, and this can be used also on Neptune 3, Ender 3 and clones. ... ## BOM |Part|PCS...

My aquarium is a robust 1 1/8 inches thick. The WAV magnet has a limited range of about an inch, so I required a new mount to ensure secure alignment. This custom-designed mount can hold two powerful BY0X08BR-N52 magnets from KJ Magnetics and aligns...

I designed this because I used the Ender 3 Filament Roller and didn't like that it did not incorporate the Original Threads. So instead, I designed this. Let me know what you think. ...If tolerances need updating let me know!

Tools for Iphone Timelapse Need : <a href="https://www.amazon.com/Bluetooth-Smartphones-zttopo-Wireless-Compatible/dp/B07MR1PHPZ/ref=sr_1_2?dchild=1&keywords=photo+shot+bluethoot&qid=1628916953&sr=8-2">Wireless Camera Remote Shutter for...

greatly improves the resolution in the z axis at first it goes in quite tight but that's how it should be with time it adjusts to the rod and it slides super smooth With this I have managed to print with a resolution of 0.1 without practically...

<p>Probably too many cage nuts &amp; screws, but it works. ...&nbsp;I've got a 2020 end cap that works very well.</p><p>2020 End Cap: <a...

i create to thing for change the board and Display to BTT SKR Mini E3 V2 and BTT TFT 35 E3 V3 The cover is open , i have 2 Fan in The IKEA LACK colling the electronic

This is my Version "ONE" of the Printheadcover for a 3-Fan-setup. (4010 Radial Fan) - A easy clean design for the Fan from Dust. - Cable space on the right side. - BL Touch cable holder. - A non hot glue attachment for the two side fans -...