elegoo neptune 4 pro 3d models

Watch the video here for 5 upgrades: https://www.youtube.com/watch?v=lnS8-vPYLtc Here are 5 more: https://www.youtube.com/watch?v=FfPitWd7eG0&t=3s This design uses the IPhone headphone to make a timelapse

Hide the coiled lead. Keeps the lead up off the ground. I rarely take the console out of its dock. Helps to keep dangly bits to a minimum... Print at any setting. This one was done roughest setting and a speed of 100mm/ps. Took just over an...

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gBJxy5yGLHS

Made an identical second spool holder to add some symmetry. ...Also handy to have a second colour already on the spool if you want to do dual-colour prints.

Catch-all for anything you may need while printing

I wanted a big refuse tray that couldnt get pushed under the build plate. ...This is what i came up with.

Here are some corner guides to make laying the magnetic build place a lot more consistent. ... Designed for use with 3M double sided tape, these provide enough clearance for the auto bed levelling feature (as previous other designs ended up colliding...

the model in the pictures has some custom lettering on it that I removed from the STL File. It snaps into place and is sturdy without any hardware. I did not include any holder for the snips as I keep them somewhere else. Its worth noting that this...

I adjusted the sizes for a narrower SD card holder.

My exturuder cable was touching to bed surface and other printed objects. It sometimes causes problems, especially when I try to print in a sequence. So, I designed a basic riser to lift cable a couple of cm. You need to use 2 M3 screws and...

Adjusted memory card slot, USB slot, and large wrench slot

The four files are all slightly different and are not interchangeable. The two parts for the back stick out a bit due to size limitations. It's easier to print them upside down. After printing, you can use the original screws to install them. I...

Spool spacer for Elegoo Neptune 2 (may work on other printers). Allows the filament spool to unroll smoother. ... 35mm inner hole 70mm outer diameter 60mm height

A simple filament guide for a second spool for the Elegoo Neptune 3 printer. ... V2 is an updated version which better fits the spool holder.

Espaceur à ajouter sous l'unité de détection du filament lorsqu'on remplace l'extrudeur original par un extrudeur aluminium double engrenage sur imprimante ELEGOO Neptune 2. ... Spacer to add under the filament detection unit when replacing original...

Bltouch mount for the Elegoo Neptune 2. Just need two M3x5 pan head screws to mount it. BLtouch can be configured with MKStool or use the provided configs. Here is the config file I came up with (Wifi enabled): https://pastebin.com/gBUZL08g This...

The Elegoo Neptune 2's psu isn't that well made and one of the corner is sagging. This support should help with that problem. ...I printed this with 15% infill.

Hi i remixed this Direct drive BMG mount for Elegoo Neptune 3 It fits my Elegoo just fine Make sure to messure out the bowden before assemble =P My extruder handle turns downwards in front so if you place your BMG on the table exit up enter down the...

:)If you have a 2D check out this mounting option instead: https://www.printables.com/model/235786-elegoo-neptune-2-2s-2d-dual-m4-extruder-mount though you should be able to make this work for both extruders if you prefer.After assembly you will...

Mounting this to the Elegoo Neptune 2 will need longer screws then the ones that are on it. (I had to use 20mm m3's to mount it.) This guide helps to get the filament straight into the filament sensor. The wheel will not need any supports. ...A 608...

Elegoo Neptune Filament Idler. This is a quick print that comes in two versions. One with and one without a required 608 skate bearing. You will need to print only one -- either with or without a 608 bearing I prefer the one with the press fit...

Here`s a bed levelling test I created by myself for the Elegoo Neptune 2 single extruder version. I used it, to calibrate my z-offset. I recommend to lower the printing speed, so you have enough time to react adjust your bedlevelling. ... Have fun...

It will allow you to mount an E3D Hemera XS Direct Drive Revo combo to an Elegoo Neptune 4 Max. It also has a mount for the Beacon Probe at the bottom. Basically after you print this you'll need to add JST ZH 1.5 connectors to the fans, the LED (24...

If you printed the previous version and you have no issues, there is no need to download this new version.If you want to protect the long cables of your Elegoo Neptune 4 Max and prevent them from hindering your prints, tangling on them or hooking...

Any updates and makes will generally be available via the model's Printables.com page.The nozzles for the Elegoo Neptune 4 Plus and Neptune 4 Max are longer than your standard nozzles, and therefore don't fit (or fit well) into many of the available...

Hi friends, For my Neptune 2s, I modified a belted z mod to fit the neptune 2 frame. The original mod is based on 2020 frames (Ender 3) and therefore it would not fit. Im to lazy to design a good powerbox. And everything is drawn based on the...

This is a simple filament guide I designed for the Elegoo Neptune 2. I wanted something to hold metal eye hooks, as I figured it would be less friction than a PLA loop. It screws into the space where the filament runout sensor is on a stock Neptune...

I really liked the camera mount I had for my Ender3 S1 Pro and thought it might fit on my Neptune 4 Plus. I took some measurments, shrunk it and added the notch and it almost worked. It was super tight which is the original file posted. Once I...

Remixed to fit the Neptune 3

For the button pins a 0.4 mm nozzle would be better.a) Backplate:0.3 mm layer height30 % grid infillno supportb) Top/Case:0.2 mm layer height30 % grid infillno supportc) Button pins (3 pieces):0.1 mm layer height100 % concentric infillno supportsmall...