elegoo neptune 3 forum 3d models

Mount adapter for moving stock spool holder to right front corner, increase print stability and reduce printer dimensions of Neptune 3 Pro.It is fully compatible with console relocation adapter: https://www.thingiverse.com/thing:6394743Mounting brace...

Neptune 3 Spool holder, NO METAL PARTS NEEDED, no bearing or threaded rod, Just print and use. Tip, you may have to sand/file down the seam that the printer leaves on the inner spindle. Based an idea from the excellent XMAN_Prints spool holder. ...

Předělaný model Elegoo Neptune 3/3PRO Cable Chain Redesigned model Elegoo Neptune 3/3PRO Cable Chain

... it runs great after tuning E steps. ...Check my youtube channel for a video on installation with the Neptune 2 (almost the same machine, different adapter plate). www.youtube.com/theferalengineerPrint with 4 walls, 60% cubic or gyroid infill.

Model has same height with orijinal bed spacer so you dont need to calibrate your bed again. ...You can use it in 3 corners if you want. ...Im using in 2 corners to easily align the Magnetic PrintbedNote : Print it with at least PETG with supports.

This was remixed from the Raspberry Pi 3 PSU Case from eric-anastas. I shrunk down the hole for the ports and changed them to fit the pi 4. If tolerances are too tight might have to use detail files. ...Just comment down below and I'll adjust.

I drew a stock model of the motherboard cover. ...In the attachment, as usual, the source file Inventor.

this replaces the need to have the spool attachment installed to mount the run-out sensor. this uses the hardware that comes with the machine, which normally holds the spool holder. ... I have my spools mounted to the wall above my printers so I have no...

Here are some corner guides to make laying the magnetic build place a lot more consistent. ... Designed for use with 3M double sided tape, these provide enough clearance for the auto bed levelling feature (as previous other designs ended up colliding...

- LITTLE BRIDGES - PLA, ABS, ETC

Watch the video here for 5 upgrades: https://www.youtube.com/watch?v=lnS8-vPYLtc Here are 5 more: https://www.youtube.com/watch?v=FfPitWd7eG0&t=3s This design uses the IPhone headphone to make a timelapse

I adjusted the sizes for a narrower SD card holder.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gBJxy5yGLHS

This simple tray to help you keep your environment clean. ... It snaps on the screews so it doesn't move.

Covers the screen

Using this item, you can store small items such as nozzles and nuts.

X-axis limit switch for installation of MGN12 rail. ...I am also attaching the Autodesk Inventor .

The stock limit switch of the X axis. ...I also attach the Autodesk Inventor file.

This was remixed from the original for the Creality CR10(https://www.thingiverse.com/thing:2412647). There are two different ones that i am including. The first one will fit the original hot end case that came with the printer. ...The second one will...

Simple cover for the Spoolholder to cover the open hole!!

Remixed for it to be somewhat adjustable, as well as a little bit thicker.

Remixed from the remix, as I wanted to reinforce a few parts as well as make it a little bit shorter.

not really a remix but inspired by Zaverdys design. ...Fits the top left corner and holds only the scraper.

I wanted a big refuse tray that couldnt get pushed under the build plate. ...This is what i came up with.

Hide the coiled lead. Keeps the lead up off the ground. I rarely take the console out of its dock. Helps to keep dangly bits to a minimum... Print at any setting. This one was done roughest setting and a speed of 100mm/ps. Took just over an...

A small part to replace the R shaped clamp to bend the wire a bit up preventing it hanging on the bed. The original screw can be used. you need two small zip ties. Caution: Be aware with this part you limit your maximum printing height! ... I used it...

Made an identical second spool holder to add some symmetry. ...Also handy to have a second colour already on the spool if you want to do dual-colour prints.

Found my Led strip coming loose, so a quick 11-minute fix, LED COVER, print in white or clear, OR if you like color try red. ...

My exturuder cable was touching to bed surface and other printed objects. It sometimes causes problems, especially when I try to print in a sequence. So, I designed a basic riser to lift cable a couple of cm. You need to use 2 M3 screws and...

The four files are all slightly different and are not interchangeable. The two parts for the back stick out a bit due to size limitations. It's easier to print them upside down. After printing, you can use the original screws to install them. I...