elegoo neptune 3 forum 3d models

This is a belt tensioner for the x-axis of the Neptune 2 and 2S from Elegoo. Since the geometry and the structure of the X-axis differ greatly from the Ender, the complete body had to be rebuilt. Since the working data is not available, I have...

When trying to make or customize hot end holders, fan holders, fan ducts for my Neptune 3, getting them to fit just right has sometimes been an issue. This is just the hole template for the carrier of the Neptune 3. It is not the same as an Ender 3...

Any updates and makes will generally be available via the model's Printables.com page.The nozzles for the Elegoo Neptune 4 Plus and Neptune 4 Max are longer than your standard nozzles, and therefore don't fit (or fit well) into many of the available...

So, I found a design on Printables by Jacob Scutzlas (655765-elegoo-neptune-4-max-build-plate-alignment-tabs) that had potential and initially started remixing it, but eventually just copied a lot of the measurements and started over from scratch. I...

This is a simple glue stick holder that attaches to the side of your Neptune 3 Pro. ...I made this by using the clamp geometry from the remix file, making it slightly sharper, and building the rest of the model around the stock glue stick that came with...

This uses the stock 4010 fans on Neptune 3 Max No bolts to hold as it's nice and tight, just push in the fans after attaching to extruder. Furthest edge from nozzle can be pushed in all the way until it stops , then carefully push & level out the...

... for Elegoo 3 Plus. ...I I got the idea https://www.printables.com/model/354402-sunlu-s2-mount-for-elegoo-neptune-3-proplusmax, which is for S2.It is in two pieces so no supports needed, you can glue or use bolts.I have used PETG but PLA will be ok.

I had an issue like many other with the X gantry on my neptune 4 max got out of wack from shipping. ...This will help you to realign the X gantry.

I have my Neptune 3 Max sideways against a wall and was tired of going around to look at the screen to operate or check progress. This mount uses the 3 factory holes and same screws to the printer frame. All that's needed is (2) #6 x 1/2" long sheet...

Fitment for Neptune 3.This is an upgraded fan shroud for the Neptune 3 platform to add dual 5015 blower fans. Each blower fan utilizes its own duct and exit as pictured in the cutaways. Fans simply slide onto their slot and get secured with 2 screws...

Yes, you read the title right, I have found a way to print on glass on the Neptune 3 Pro, the Neptune 3 Plus, and the Neptune 3 Max. The sensor on the Neptune 3 Pro only is able to sense metal so when you try to print on glass it just rams the head...

I was using my Previous print on glass mod for the Neptune 3 Pro, Neptune 3 Plus, and Neptune 3 Max and I noticed a big problem. When the printer would auto home the leg on the mod would fall below the bed, this would cause it to get ripped off when...

A remix because the original one was mounted from the top and it was wobbly so I made remixed it so it could be mounted using the two mounting holes on the back of the biqu h2.For mounting it you need 3m3 screwsInstallation steps:1-mount the biqu H2...

Another style of tool holder for the Neptune 3. This mounts to the top right corner of the gantry and tightens down with two bolts and the mount bar. When attached there is plenty of clearance for the machine to work as normal. unless direct drive...

I really liked the camera mount I had for my Ender3 S1 Pro and thought it might fit on my Neptune 4 Plus. I took some measurments, shrunk it and added the notch and it almost worked. It was super tight which is the original file posted. Once I...

 I assume always having the filament rub on the underside at this 45° angle would wear it out faster then when it's mounted paralel to the path of the filament. I made a 45° bracket to mount the filament runout sensor ontop of the Neptune 4 Pro, Plus...

This moves the neptune 3 pro bed leveling probe down by 3.25 and over by 3.5. I needed it after an all-metal hotend upgrade caused my nozzle to be too low for the probe to work in the stock location. You will need an M3 screw and M3 nut as well...

Add Elegoo Neptune2 printer and restart. OR If you have set up any other printer profiles in the previous Cura version and do not want to lose them using the "reset" option First, backup your definitions, extruders and meshes folders in your...

THIS WILL DELETE ALL PRINTER CONFIG INFO AND PROFILES. Restart Cura 4.12.1 to ensure errors have gone. Re-install the Toylerrr plugin and restart. Add Elegoo Neptune2 printer and restart. OR If you have set up any other printer profiles in the...

Simple 235x235 bed level test for the Neptune 3 pro that takes up the whole bed, so u can make sure you have the whole bed dialed in, first use the single centered test to dial in your z height, then use the five square test to get the whole bed...

In the future I will design a tool holder, it will hang off the side of the LCD_Hole_Insert.Everything can be printed with the same settings, some support is required but the settings I use generate the support only in require areas.I printed in...

Just a quick remix of the motor cap connector for this excellent cable chain. Added some hexagon holes to help with heat dissipation. ... 20% infill 0.15 Layer height Supports may be needed

Since all Z-stabilizers seemed more complex than needed I stepped forward to quicklydesign a new one.

I found my usb port was not as secure as i would like so i put this together. ... I placed 2 holes and a groove to add a Zip tie

Fine tuned version

I love the HeroMe Hotend system, but ran into problems with my printer, one being the firmware being a headache to adjust and modify, and that my hotend because a dual extrusion type would not fit correctly either. So I made my own hotend that lets...

EDIT 04/10/20 : I MUST REMAKE IT (i got some issue with the hardness and the stability) Support made to hang on the X axis Motor. I used the camera box from AUSTIN3PRINTING because i didnt wanted to build it by my self^^ Here the link :...

I modified the original design slightly to accommodate for a dual extrusion hotend that comes with the 2D variant.

EDIT 04/10/20 : I Need to Redo It (I Had Some Trouble with the Hardness and Stability) Support Made to Hang from a Motor on the X Axis. I Used the Camera Box from AUSTIN3PRINTING Because I Didn't Want to Build It Myself. Here's the Link:...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...