elegoo neptune 3 forum 3d models

This is the (Left) X-Axis Cover remixed from SebastianRubner's tension stopper design.You will need to unplug the connector to install this. ...I would recommend doing this while the printer is off.Tip: (Unplug the connector, push the connector into the...

This is a remix for 688zz bearing.Original model: https://www.thingiverse.com/thing:5804993

Left Side filament guide. ...This version needed a 49" spacer between the arm and the threads to align the filament drop in with the End of Spool Sensor

This should allow you to remove the stock magnetic ABL sensor and replace it with a Beacon (low-profile Rev D) using existing holes in the stock housing and screw in the optimal position.I'm not sure if it will work with other models, but it should...

Modified sensor holder for when you have two spools on the rack

<p>Handle has to be glued into drawer hole. I suggest Gorilla glue or some sort of super glue so that there is no worry about the handle coming off. The fitment of the drawer into the machine is tight but loosens up nicely as time goes...

Remixed from the side cutter holder design for the same printers. ...Made to guide the filament through the middle of the spool holder for those who use 2 spools on the printer.You'll also need to relocate the filament sensor to the middle.No supports,...

Replacement for the standard part, as it isn't wide enough in the middle to allow exchanging the plastic mounts for silicone ones. I had to cut the old part off and acetone weld the replacement part to make it work, but your milage may vary. I...

I consider this a rough draft, but it is a working install. Still need to fine tune things.Files remixed to fit the left side location of the factory induction probe. The probe dock was modified to fit the botton lug of the X gantry and extended a...

This is my solution to moving the display to the left side of the printer. From the original holder I took the magnet. The holder is divided into three elements for easy printing. ...They are glued together with glue.

I made a spool holder to add the ability to use spools with a small hole.

I wanted the frequent use tools right to hand and the rest out of the way. This was the best option for me. The tool caddy is mounted on the left side of the base. Just shove the clips in until they click in place. It holds nippers, scraper, USB...

I didn’t guess a little with the dimensions of the latches (dangling a little) and left a link to the file from Fusion 360 if someone wants to modify the model (https://drive.google.com/file/d/15JK92a8lGJnJ8iEZb2aF1_Fy3FbUeA1i/view?usp=sharing).

Buddy randomly uses a blink doorbell to spy on his printer so I added a wedge mount for his doorbell onto the tool holder (not sure who to attribute the tool holder to because he just sent me the STL). ...Works great.

Replacement for the standard part, as it isn't wide enough in the middle to allow exchanging the plastic mounts for silicone ones. I had to cut the old part off and acetone weld the replacement part to make it work, but your milage may vary. ...I...

Simple tool holder for tools shipped with the 3D printer. The tool holder is assembled from 2 parts.ASSEMBLY: I recommend gluing parts together. ...if you decide to glue parts together first screw bolt in and mark the upper side, so you don't end up...

I didn't like where the threads were located on this. My spool kept sliding over to the side and eventually onto the wheel, so I moved them down. ...So far it's been holding up fine and hasn't come unscrewed.

this is a mount to turn your touchscreen/control 90 degrees. works well when printer is sideways on a stand. ...moved one mounting hole may need drilled slightly to fit.

Abdeckung für einen Fiberpunk Node Max um die Kabel zu verstecken

Removed the BL Touch mount, adjusted the holes on the back (made them wider & actually go through).

My printer (Elegoo Neptune 3) is back from the front of the table it's on about a foot or two, so I wanted a floating stand to keep the controller propped at an angle but allow me to move it around freely. ... This is my first shared design, so any...

Ein Halter mit Gehäuse für die PiCam bestehend aus 3 Teilen, Gehäuse und Arm.Einfach zusammen schrauben und fertig.Keine Supports nötig

Webcam Mount for Elegoo Neptune 3 pro

I designed this remoteholder for attaching it beneath my Neptune 3 pro encloser. I´ve used two screws. ...

I needed a screen cover for my neptune 3 to print at night because it stays in the bedroom and is also useful to protect screen.

tongs holder for neptune 3 / pro or maybe even ender 3 fdm printer. ... printed with blue pla from 3d jake 20% infill 0.2 mm layer distance 200 degrees nozzle 60 degrees bed

Simple tool holder (like many others) for the Neptune 3. Wanted to make one where the tools sit on the rear of the printer, above the power supply. so i did! ...

Uploaded a model of the neptune 3 pro - 1:1 so scale accordingly. Have not tried to print yet. Have you ever wanted a mini me? I will attempt it at 20% scaled down. ...Probably will need supports.

Simple tool holder for all the tools supplied with my Neptune 3. Bolts to the top of the gantry so tools won't interfere with tall builds. ...Holds spatula, two screw drivers, 6 hex key, 2 spanners, flush cutters and the usb/microSD card reader.Minimal...

Hi, so i set a Direct Drive on my Neptune 3 i couldn´t find a filament holder to go with, so i designed one, is really simple, is my first ever design on 3D so, any constructive criticism is welcome, any feedback!updated the model, so now can be used...