elegoo neptune 2d 3d models

Elegoo sent me these STL files for a dual z drive setup. ...If you get the creality dual z drive kit I don't believe you will need the wheel bracket.

I will add the other Neptune printers if someone provides measurements.Another Tip to save frustration. If you install the Z rails make sure the X-axis is square to the upper frame before tightening the X to Z rail bolts. I did this by simply...

Loved this design from Code Monkey Zero, however unfortunately it isn't compatible with the Neptune 2's stock BL Touch mount on the X axis carriage - I've added a mounting plate that is as close as possible to the original stock BL touch mount points...

I added a BLTouch mount to Tal's Neptune 3 Fan shroud, this enables greater flexibility in hotend choice and significantly speeds up bed leveling. I also shortened the duct slightly as the original version had the duct very close to silicone sock and...

Designed a Storage (drawer) for tools for the Neptune 2 and Printed it on it. It fits in the Bothe sides of the Printer. Maybe it fits into the Ender V3 if its the same 40x40 aluminum profile. If you this helps and want to encourage my...

Decided to make my own Tray/Nozzle Holder for the Neptune 2S. Holds the 4 included nozzles, the 2 bowden tube holders, and the Extra clips. When printing I added extra support to the end of the narrow section to help with adhesion, you may...

Created a Cam Mount to fit my Logitech C270 Cam on my Neptune 4 Plus. I like too monitor my print so this print is made so spot directly at the nozzle. You can tilt the cam so only nozzle is visible and a lot of the print.Does fit to the right side...

Moin, ich hab mir die in der black week 2,3 kg Rollen von Redline Filament bestellt und musste feststellen, das die gar nicht auf den originalen Filamentroller vom Elegoo 4 max pro passen :D, daher hier mein angepasster Filamentroller für bis zu 30cm...

I upgraded my Neptune 2 with a BMG extruder clone and because of that the filament sensor and guide wheel I had in place did not fit anymore. Made this adapter in Onshape and included the guide wheel in the design, so it's only a few parts to print.

I upgraded my Neptune 2 with a BMG extruder clone and because of that the filament sensor and guide wheel I had in place did not fit anymore. Made this adapter in Onshape and included the guide wheel in the design, so it's only a few parts to print.

| Stock : Direct axial loads to the Z stepper | This holder : Reduces loads to the Z stepper | | ---- | ---- | |  |...

... change. The Elegoo magnetic display mount attaches to this one with the same 3 screws it came with. The camera holder is from https://than.gs/m/751499. ... The original display holder is from https://www.thingiverse.com/thing:5765043

This is a Remix from Neptune2 Elegoo Non display side tray from Fabius_Bile I have removed some unecessary stuff like the hiden storage its a good model but I decided to remove that and also one of the wall to get more access to the SD card slot.

I wanted to clean up the Z-axis wires on my Neptune 2S, they've touched the table and lead screw during a print before. This cable cover has a nice pressure fit, but also the filament detector screws can be used to fasten it. I use it together with a...

I've created my own implementation of the following cables clip design:https://www.printables.com/model/722500-enhanced-anti-drag-cable-holder-clip-for-elegoo-neMain differences:Can be printed without supports;Cables are fixed in place so you do not...

It slots nicely onto the right hand side right next to the x-axis belt tensioner.There is a cable guide for the wires that will go to whatever you're using to take the photos (I'm using a Raspberry Pi 3b).To use the time-lapse feature, use the Elegoo...

This is for people who already have a printer and want to upgrade, if you are thinking Neptune 2S vs Neptune3 its probably worth to just get a Neptune3. You could apply this concept to any printer really but need some different prints.Going crazy on...

Da der Boardkühler des Neptune 2 sehr laut ist, hab ich diese Abdeckung designed, um einen 80x80x25mm Lüfter direkt über das Board platzieren zu können. Um die Abdeckung nutzen zu können, muss der Drucker mindestens 30mm höher gelegt werden. Dazu hab...

After deciding that the original cable clip that came with my Neptune 4 Max was designed by a sadist, I decided to create my own. This one is designed to hold the cable flat and out to where it doesn't rub on anything and also keeps it from block the...

 ## Compatible printers I confirmed this working on ELEGOO Neptune 2, and this can be used also on Neptune 3, Ender 3 and clones. ... ## BOM |Part|PCS...

Remix of https://www.thingiverse.com/thing:4949488

Spool holder for smaller spools

Some simple adjustable feet, inspired by need and other designers. ... This object was made in Tinkercad.

Tools for Iphone Timelapse Need : <a href="https://www.amazon.com/Bluetooth-Smartphones-zttopo-Wireless-Compatible/dp/B07MR1PHPZ/ref=sr_1_2?dchild=1&keywords=photo+shot+bluethoot&qid=1628916953&sr=8-2">Wireless Camera Remote Shutter for...

I designed this because I used the Ender 3 Filament Roller and didn't like that it did not incorporate the Original Threads. So instead, I designed this. Let me know what you think. ...If tolerances need updating let me know!

The mount attaches to the left side of the printer using these https://www.thingiverse.com/thing:3050607. ...The mount uses a 1/4 camera tripod screw https://www.thingiverse.com/thing:578514 so you can attach any camera or even a phone using this...

Piece revised to screw directly into M5 screws

This is my Version "ONE" of the Printheadcover for a 3-Fan-setup. (4010 Radial Fan) - A easy clean design for the Fan from Dust. - Cable space on the right side. - BL Touch cable holder. - A non hot glue attachment for the two side fans -...

Tools for Iphone Timelapse Need : Wireless Camera Remote Shutter for Smartphones The support does not require any fixing, it clips perfectly, the button is fixed with 2 M3 screws. I have included the gcode in the zip. ...I am using Prucaslicer, place...

I only occasionally need the Filament Runout Sensor and the remainder of the time it is in the way of loading the extruder. I decided it would be easy to design a hinge that would allow me to flip it out of the way when not needed but quickly deploy...