elegoo neptune 2 upgrades 3d models

This is an X-axis belt shim for ELEGOO Neptune 2 series 3D printers.It makes the X belt parallel to the X axis (gantry) and equalizes the nozzle travel scale over the all position on the axis.Therefore, the accuracy of the printing is...

Print Settings Printer: Elegoo Neptune 2S Rafts: No Supports: No Resolution: 0.15 Infill: 30 Filament: Your choice PLA Your Choice Notes: You may need to sand/file after printing since the holes may have slightly collapsed but it should be fine...

This is a custom/remix for a Elegoo Neptune 2S. The spacers on the underside of the part attached to the 3d printer structure were removed, for a better fit of the screws on the Y axis bar. ... You may have to force the part a little bit into the...

Hey this is my modified mount for a automatic bed leveler to go with the mini Satsana fan ducked before a elegoo Neptune two, three, 2S, 2D I modified it so that it was easier to screw it in on to the plate otherwise the bottom screw was impossible...

This is a custom/remix for a Elegoo Neptune 2S. The spacers on the underside of the part attached to the 3d printer structure were removed, for a better fit of the screws on the Y axis bar. ... You may have to force the part a little bit into the...

For the button pins a 0.4 mm nozzle would be better.a) Backplate:0.3 mm layer height30 % grid infillno supportb) Top/Case:0.2 mm layer height30 % grid infillno supportc) Button pins (3 pieces):0.1 mm layer height100 % concentric infillno supportsmall...

... performance and stability of a newly installed version. EDIT 2: If you get a 404 error using the "Download all" option you can download the file from the "Thing Files" link under the main image or from Thangs https://thangs.com/mythangs/file/37447

THIS WILL DELETE ALL PRINTER CONFIG INFO AND PROFILES. Restart Cura 4.12.1 to ensure errors have gone. Re-install the Toylerrr plugin and restart. Add Elegoo Neptune2 printer and restart. OR If you have set up any other printer profiles in the...

Just recently I got a Netune 2 and after my extruder stepper started making noises based on the filament tension (the heavier the spool, the worst) I started searching for a solution from the community. I loved [MantisGod01's...

In the future I will design a tool holder, it will hang off the side of the LCD_Hole_Insert.Everything can be printed with the same settings, some support is required but the settings I use generate the support only in require areas.I printed in...

These are designed in 1-4mm sizes. The clip directly to the bottom of the Z gantry - you can use a little thin double sided tape to keep secure as well. ... Basically, this allows you to adjust the Z endstop height if you are using a longer/ lower...

Just a quick remix of the motor cap connector for this excellent cable chain. Added some hexagon holes to help with heat dissipation. ... 20% infill 0.15 Layer height Print standing up with supports for best results.

asdfghjklkjhgfdsasdfghjklkjhgfdsdfghjklkjuhygtfrdsasdfghjkjhgfdsasdfghjklkjhgfdsdfghjklkjhgfdfghjkjhgfdsdfghjklkjhgfdfghj

ELECTRONICS 4010 REPLACEMENT COVER V1: Fan gets blocked by the ribbon cable but can still be used V2 (Currently Working on): Fan will be moved lower, I'll add places to mount Buck Converters and accessible without opening the Electronics Case.

<p>This was remixed from the Raspberry Pi 3 PSU Case from eric-anastas. I shrunk down the hole for the ports and changed them to fit the pi 4. If tolerances are too tight might have to use detail files. ...Just comment down below and I'll adjust.</p>

simple lead screw knob, is a tight press fit onto the lead screw

<p>Using the X stepper motor but with 15 mm screws. ...Works great with:</p><p><a...

Did this remix to accomodate the spatula that I got with the printer and modeled it to fit on the back of the printer and to not interfere with the gantry. ... Also added a slot for a pair of tweezers.

Fine tuned version

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

No need for screws. Just slide it into your 4040 extrusion on the RIGHT side. This should be compatible with any webcam that you can hang on a monitor. ... my PayPal is mathejadavid@gmail.com Please send me around 1$ or more over PayPal if you...

Just a quick remix of the motor cap connector for this excellent cable chain. Added some hexagon holes to help with heat dissipation. ... 20% infill 0.15 Layer height Supports may be needed

This was remixed from the original for the Creality CR10(https://www.thingiverse.com/thing:2412647). There are two different ones that i am including. The first one will fit the original hot end case that came with the printer. ...The second one will...

This is my "Proteus" printheadcover for a 3-Fan-setup. i designed this after encountering problems of "too hot corners". ... to buy: 40x10mm directionalfan (Creality-3D-40+40+10mm-DC24V-0_1A the one I used) to do: soldering (not...

i dont know how in the world to use cad, but I frankensteined this https://www.thingiverse.com/thing:4835981 to accept a chain link from https://www.thingiverse.com/thing:4932649 . ...its ugly, but it works.

It consists of: Tool box. It goes on the upper bar and allows you to keep your tools tidy. It also has space for tweezers. Filament guide. It is placed over the filament end detector and serves to decrease the tension. It can be placed with the...

Tool holder with two holes to screw on the wall.

print simple "ELEGOO NEPTUNE 4 PRO - FILMENT GUID" in 2 min.