elegoo neptune 2 replacement parts 3d models

These are designed in 1-4mm sizes. The clip directly to the bottom of the Z gantry - you can use a little thin double sided tape to keep secure as well. ... Basically, this allows you to adjust the Z endstop height if you are using a longer/ lower...

Just a quick remix of the motor cap connector for this excellent cable chain. Added some hexagon holes to help with heat dissipation. ... 20% infill 0.15 Layer height Print standing up with supports for best results.

Fine tuned version

Just a quick remix of the motor cap connector for this excellent cable chain. Added some hexagon holes to help with heat dissipation. ... 20% infill 0.15 Layer height Supports may be needed

simple lead screw knob, is a tight press fit onto the lead screw

<p>This was remixed from the Raspberry Pi 3 PSU Case from eric-anastas. I shrunk down the hole for the ports and changed them to fit the pi 4. If tolerances are too tight might have to use detail files. ...Just comment down below and I'll adjust.</p>

This is my "Proteus" printheadcover for a 3-Fan-setup. i designed this after encountering problems of "too hot corners". ... to buy: 40x10mm directionalfan (Creality-3D-40+40+10mm-DC24V-0_1A the one I used) to do: soldering (not...

asdfghjklkjhgfdsasdfghjklkjhgfdsdfghjklkjuhygtfrdsasdfghjkjhgfdsasdfghjklkjhgfdsdfghjklkjhgfdfghjkjhgfdsdfghjklkjhgfdfghj

Tool holder with two holes to screw on the wall.

i dont know how in the world to use cad, but I frankensteined this https://www.thingiverse.com/thing:4835981 to accept a chain link from https://www.thingiverse.com/thing:4932649 . ...its ugly, but it works.

print simple "ELEGOO NEPTUNE 4 PRO - FILMENT GUID" in 2 min.

Elegoo Neptune 3 plus parts draw Should fit the Pro and max. ...Let me know in the comments if you use it on other printer :-) May fit othere printers Print 2 and have one on each side :-)

Elegoo Neptune 3 plus parts draw Should fit the Pro and max. ...Let me know in the comments if you use it on other printer :-) May fit othere printers Print 2 and have one on each side :-) Category: 3D Printing

Předělaný model Elegoo Neptune 3/3PRO Cable Chain Redesigned model Elegoo Neptune 3/3PRO Cable Chain

I'm am replacing the zip ties on my Elegoo Neptune 2s. ...This part will replace the zip tie that is on the cable on the back of the hotbed.I printed this with PETG Duramic 3D ( https://a.co/d/gNwqRij )

Elegoo Neptune Z Axis Stabilizer for better Printing

Another Elegoo Neptune 3 pro cable holder.Print without support

Remix of Elegoo Neptune M4 Extruder Mount that fits https://www.printables.com/model/259303-elegoo-neptune-m4-extruder-mount

Full plastic (exept for bearings) spool holder for Elegoo Neptune 2, 2s printers. ... Size for 6201 bearings (d=12mm, D=32mm, B=10mm)

Also see my LED difusor remix for Neptune 3 pro https://www.printables.com/cs/model/665424-elegoo-neptune-3-pro-light-bar-slim-diffuserZ mount is made from 2 pieces GLUE them togetheraround 36 chains will be needed around 42 clips will be neededother...

This is the same tower but the gcode is for an Elegoo Neptune 3 from the Elegoo(Cura) Slicer. ...

This is a mount for the Elegoo Neptune 4/pro runout sensor, if you don't want/use the filament holder. ... you will need 2 M3x6mm heat-set threaded inserts for the screw that came with the filament runout sensor

this is a tool holder for the elegoo neptune 3 plus

https://www.printables.com/model/681244-elegoo-neptune-2s-dual-fan-5015-upgrade-direct-dri

Fan Duct with radial 5015 fun for Elegoo Neptune 3 Pro

Side mount USB holder for the Elegoo Neptune 3 Pro Printer

I made this model as i removed the filament sensor because it caused too much friction when printing tpu, since on retractions the filament would bend instead of going back through the sensor, it would falsely trigger, stopping the print. With this,...

A tool holder for the Elegoo Neptune 3 Pro that mounts to the other side of your spool holder

A Bracket to hold the filament runout sensor on Elegoo neptune printers when not using the standard filament spool holder.

this is a tool holder for the elegoo neptune 3 plus https://www.crealitycloud.com/en/user/3626193967