elegoo mercury plus 3d models
61528 3d models found related to elegoo mercury plus.thingiverse
This is a turntable for Elegoo Mercury plus. ...Easy to print and works just fine.
cults3d
This is a stand to make the elegoo Mercury Plus the same height as the Elegoo mars. the corner pieces are all the same and the panels that join the sides are the same, with different designs, along with a blank one too add your own design. ... M3 x 12...
thingiverse
ISSUES The start > wobble > stop> restart works 6 /10 on the elegoo mercury plus The wash cycle was to gentle for me Materials Simple known how to open up your machine If its in warranty reach out to elegoo If its out of warranty like mine tinker and...
thingiverse
Wanted to find a place for the acrylic plate (turntable) used to spin a model around on the Elegoo Mercury Plus so I made this to mount to the side of the case. ...Uses original screws.
prusaprinters
Wanted to find a place for the acrylic plate (turntable) used to spin a model around on the Elegoo Mercury Plus so I made this to mount to the side of the case. ...Uses original screws.</p>
thingiverse
##Elegoo Mercury Plus turntable shelf For usage with the original metal plate and old CD Blank (just cut a little bit in the holo foil and remove it easy with sticky tape) Can be printed without support - do a little sanding when the fit is too...
thingiverse
This magnetic impeller assembly, originally designed for use with the A/Cubic wash/cure station, also works great with the new Elegoo Mercury Plus. Thus to make it easier for the owners of the Mercury Plus to find it, I just removed the base ring...
thingiverse
Elegoo Mercury Plus adapter NOVA3D Bene4 Mono filament PETG 100% -
thingiverse
This is a holder for the rotation plate of the Elegoo Mercury Plus. Glue it with some double sided tape to the side of the body of the device. This way the rotation plate is not flying around somewhere when not needed during washing mode ;-) ...
thingiverse
This is an exact replica of the bushing inside of the elegoo mercury plus cleaning tank. My bushing was .5mm to large and caused the fan to not spin. This replacement is that .5mm smaller. Printed with a Mars 2 Pro the inside is slightly too small...
thingiverse
This is a stand for the ELEGOO mercury plus curing turntable. one of my first designs its not perfect but it works. build this because the turntable kept flying around on my desk and i wanted it to have its own place. The stand has 4 holes for...
thingiverse
The basket should slot easily onto the Elegoo Mercury Plus' provided table for an easy drop-on/pull off experience. ... Provided chitubox file is what I used to print, some of the basket tines aren't supported perfectly (see image of print) but it...
thingiverse
I made this little adapter so that I could use my Anycubic Photon build plate with the Elegoo Mercury Plus. It is a small quick design that can be quickly printer and used. It is designed to reuse the main bracket hardware that comes with Mercury...
cults3d
Tray holder for the mercury plus, the goal is to be able to put the tray on the mercury hood so it is within reach and not dragging anymore. ... To stick where you want
thingiverse
Tiroir à installer sous la Mercury Plus de Elegoo, il permet de ranger plateau tournant, support plateau et divers autre accessoire. Pour l’installation il vous faudra récupéré les 4 pied en caoutchouc et remplacer les 4 vis d'origine par des...
thingiverse
Base I made to connect a common rectangle to oval ventilation piece to my Mercury Plus hood. It also got some small holes to let fresh air flow in. Just be sure to measure dimensions when ordering your plastic rectangle to oval tube connector. ...
thingiverse
I wanted a part for my Wash and Curing station from Elegoo. I dont like the original Cage for the Washing part, so i build a new one. Build with your slicer but without Top and Botton Part, Select Gyroid Infill for good stiring. ...10% should be good
prusaprinters
I wanted a part for my Wash and Curing station from Elegoo. I dont like the original Cage for the Washing part, so i build a new one.</p> <p>Build with your slicer but without Top and Botton Part, Select Gyroid Infill for good stiring. ...10% should be...
cults3d
This is a longer bracket for the Elegoo Mercury Plus, when you use the bracket for the Elegoo Mars. If you have small parts and only 1 litre cleaner in the box, the original is to short. This here is around 6cm longer. Only replace the original...
thingiverse
This is a longer bracket for the Elegoo Mercury Plus, when you use the bracket for the Elegoo Mars. If you have small parts and only 1 litre cleaner in the box, the original is to short. This here is around 6cm longer. Only replace the original...
thingiverse
I made a adapter for Anycubic Photon Zero to the Elegoo Mercury Plus.
thingiverse
I realized at some point that the Mercury Plus could be a very powerful magnetic stirrer if the magnets were positioned closer together on the spinning plate. Since I never use the wash feature, this conversion was perfect for me. The stock plate...
thingiverse
Support to allow the use of the Elgoo Mercury Plus system tank. This mount works with a 68mm high Nema 17 motor. Parts needed: 1 Nema 17 motor 1 GT20 pulley with a 5 mm axle 8 magnets 10mm in diameter and 2mm thick 1 system to control the...
prusaprinters
I made a adapter for Anycubic Photon Zero to the Elegoo Mercury Plus. ...Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 200 Infill: 10 Filament: ESun PLA Category: 3D Printer Parts
cults3d
The Elegoo Mercury Plus's tray is really not practical for pouring alcohol or water. The liquid tends to follow the wall of the pan and has the annoying habit of not flowing where you want it to. With this pouring spout that fits perfectly into the...
thingiverse
Hallo zusammen, ich habe mir hier einen Adapter gemacht, der es ermöglicht die Druckplatte des Creality LD-002R an einer Elegoo Mercury Plus Wash & Cure Station zu befestigen. Ich habe drei Versionen erstellt: Version1 ist ohne Mutter zur...
thingiverse
Keep your cover out of the way while you work! You'll need 4x M3x12 screws to replace the top 4 screws of the light tower with. ... Inspired by https://www.thingiverse.com/thing:4105774
cults3d
so i had this idea and so far it has worked out and made my life allot easier when printing lots of smaller models i know i shouldent have to say this but dont glue the legs at one side so you can stack them 50p as all just goes towards resin...
cults3d
This model is a replacement for the original one that came with the cleaning station. ...Mine stopped working so I made this out of pla and it works remarkably well.