elegoo mars fep film 3d models

Filter and heater system for Elegoo Mars/pro 2. Designed to be printed with FDM. The heater is from here: https://www.thingiverse.com/thing:3412516 Specifically this version: Mag_Heater_v22.stl Air filter is inspired by this one:...

This model is made to snap on to the existing Elegoo mars pro side paneling without needing any glue or magnets. All the other versions I've seen require you to open it up, and some even need you to drill holes into the metal case, which is a hassle...

After I noticed that the Elegoo Mars has only a fixed holder for the light barrier for the Z-axis I decided to create my own adjustable construction. After the production and the assembly of the unit shown here I could adjust the Z-axis exactly. Then...

The only modification I made to it was adding a mounting block on one side so I could attach it directly to my Elegoo Mars MSLA Printer. Nothing else was altered, and consequently I left the file names intact. Please refer to I_am_me's thing to learn...

This is a side handle for Elegoo mars or any type of acrylic cover SLA printer, the base has big surface area for the glue to hold on into it. Print instructionsCategory: 3D Printer Parts Print Settings Printer Brand: Prusa Printer: i3 MK3 Rafts: No...

This is a remix of nofear72784's model for holding a specific personal heater up inside an Elegoo Mars resin printer. In reality, this could work in any resin printer. My changes are to reduce material used, and round off the corners a bit. I...

The Elegoo Mars SLA Printer operates off a USB Thumb Drive located at the rear of the machine. This bracket contains a USB extension cable attached to the printer housing's left side via existing screw locations. To assemble this printer, besides...

This is my modification for heating module for Elegoo Mars 3, original design is by Martian Wong. The parts and wiring are the same, I used 12V 50W PTC heater insted of 100W. If you use 12V heater, all parts and adapter should be 12V. Same for...

Easy to install Scale to check Z Axis movements (repeatability) with ur Elegoo Mars Printer. Linear Guide needs to be 90 degrees in Both directions so Check this First and put some spacers under the Aluminum Rail to level it.The Hole of...

This is a custom heater bracket I designed specifically for the Elegoo Mars, but it also serves me well inside my FDM enclosures. It greatly enhances the printability of thick resins like Siraya Blu and Tenacious. Printing with PLA is no problem...

Stand I've built for my Elegoo Mars 3D printer features a lined interior with foil tape and an LED strip of black lights. The enclosure has a slide-up door that can be easily removed. Additional mount holes on the sides provide convenient access to...

This piece clips into the rear vent of the Elegoo Mars and allows a Light Dependant Resistor to sit in place to capture when the UV light comes on. This tells the Arduino to activate a relay which makes the camera take a picture. I use a Fuji...

I whipped up a rough design for an exhaust system for my Elegoo Mars 2 Pro - I'm not particularly great with cad software, so I just used Tinkercad to make it. It has a mount for a 92mm fan that I took from an old machine (p/n 166g7-a00) although...

My first publication. My first print with the Elegoo Mars showed me that I had a deviation of 1.6mm at the calibration cube in the Z-axis. After I noticed that the Elegoo Mars has only a fixed holder for the light barrier for the Z-axis I decided to...

I found out that the VATs of my Elegoo Mars Pro fit almost perfectly into a rotho storage box i found in the supermarket (no, I didn't take the VAT with me to the supermarket...). It just needed an insert to make it fit perfectly. I'm not sure if the...

Mars 3 vat is higher. ...I extend vat holder for 3mm. And mars 3 vat fits very well ;)

Because the original fan of the Elegoo Mars 3 runs all the time, is way too loud and absolutely annoying, I swapped it for a 40x40x20mm Noctua fan. To improve the cooling with this smaller fan, I also constructed an air duct to draw the warm air out...

Because the original fan of the Elegoo Mars 3 runs all the time, is way too loud and absolutely annoying, I swapped it for a 40x40x20mm Noctua fan. To improve the cooling with this smaller fan, I also constructed an air duct to draw the warm air out...

Because the original fan of the Elegoo Mars 3 runs all the time, is way too loud and absolutely annoying, I swapped it for a 40x40x20mm Noctua fan.To improve the cooling with this smaller fan, I also constructed an air duct to draw the warm air out...

I wanted to create a ventilation system for my Elegoo Mars 2 Pro to reduce the smell. I didn't have to much space and don't want to destroy my printer like gamla3d's design (https://www.thingiverse.com/thing:4699705). He did a great job by the way. ...

A stand for Elegoo Mars boasts two spacious drawers perfect for storing small accessories such as wrenches and gloves. The top features a thoughtful cutout to ensure the fan remains unobstructed at all times. If you have a USB extender handy to...

I built this custom heater for my Elegoo Mars printer to use resins that print best at 30 degrees C or higher without heating up the whole house. It's designed to sit between the printer base and cover, with a duct connected to the back that has a...

Just a simple drip pan to set a Mars 2 in to catch any wayward resin drips

Just a simple drip pan to set a Mars 2 in to catch any wayward resin drips

TPU feet for mars, depending on filament they should dampen vibrations and prevent printer slipping on table. ... I recommend printing with TPU about 75A shore hardness.

I created this Handy USB-Holder remix because I'm a right-handed user, and it's got a cool logo on the left side of my Mars. ...Thanks go out to mattinflorence for making it possible!

Get your hands on an LCD screen for a standard Mars model and then fit it with a shim to make it work seamlessly. ...With the right materials, printing out a new screen is a breeze - it's just 0.75mm thick, so you could even cut one out of a cereal box...

Need a mount for a Mars pro Printer, you can use it in any direction in the picture i have it up side down with the power cord at the top but you can turn it around and have the power cord at the Bottom, please leave a like if you download

Hey, check out this custom resin vat cover I've remixed from Xantrix, with some bold branding options - voxel design and Elegoo. I just added two more versions that give you a clear view of the resin gauge from eytec's design, featuring a cutout on...

Created a ventilation rig for my Mars Pros ATTENTION: IN ORDER FOR THIS TO WORK YOU MUST FLIP THE FAN ON THE INSIDE OF THE PRINTER TO SUCK IN AIR. Step 1: Take apart the Mars Pro and flip the fan from blowing out of the bottom to sucking IN to the...