elegoo mars 3 magnetic build plate 3d models

A Simple UV Box Design to Match the Amazon-Bought Light Quickly Created I designed a basic UV box that matches the light I recently purchased from Amazon.

A straightforward examination of the entire display is conducted to identify any defective pixels or areas of excessive heat buildup.

hauteur de pied +15mm dévisser le pied normal et remettre en place. ...permet un meilleur refroidissement de la machine et moins de compression du flux d'air, donc 10 dB en moins à la mesure

This shorter knob will add approximately 19mm of extra printing height compared to the standard knob. ... It requires a single m10x2 x 18mm bolt, some epoxy or another similar adhesive, and an optional 20mm diameter 1.5mm thick disc to cover the bolt...

I need a smalç handle for the fingers in the cover to grab it, and print it flat without supports

Customized version of https://www.thingiverse.com/thing:4745925 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4745925

By installing the epax firmware, you unlock direct access to the concealed network card within the printer. I rebuilt the backplate with a strategically placed hole that allows the network cable to protrude freely. In the image provided, the USB...

Support for the Z-axis includes a hole for M6 on the top and a larger base; simply remove the motor's bumper to access it.

I always seem to always have something in my other hand. Now I can put the lid on and off with just one hand. Printed on its side with supports. Sanded and put the less pretty side to the back. ...Some 3M sticky foam tape and you're good to go

I need a smalç handle for the fingers in the cover to grab it, and print it flat without supports

Designed to be molded from flexible materials, this item slips on smoothly, conforming perfectly to the hand it's meant to fit.

The user created a shortened knob, ensuring the lid stays firmly in place as it reaches the top of the Z-axis during maximum height adjustments of 170 millimeters. ... https://youtu.be/0Qb4zY7aGmM

Top part from https://www.thingiverse.com/thing:3797423 split in half to embed nuts (you should glue them together), also walls made thicker. ... Untested!!!!!

A Customized Edition of the USB Holder by Matt Inflorence Tailored Specifically for the USB Extension Cable from RS Components.

WARNING: Do not use this thing for FDM printing, as several successful prints later it leaked resin. Forensic post-failure analysis reveals that the two frame parts warped significantly in areas where the M4 screws pull against the main VAT body. A...

Elevate the foot by 15mm. Remove the standard foot and reinstall it. ...This allows for better cooling of the machine and less air flow compression, resulting in a 10 dB decrease in noise levels.

small scale elegoo mars 2 pro mini model that can be used to decorate your printer with another printer! I made this with Blender, i used plugins for the bolts for plate leveling. The screw for moving the plate up and down is a bit fragile, again...

This is a version of CNSHEETS PTC heater holder for the Elegoo Saturn. I think it was 45mm x 85mm for the metal that would fit the slot although you could trim it down if you wanted. Make sure the metal you use is able to attract a magnetic...

This is a version of CNSHEETS PTC heater holder for the Elegoo Saturn. I think it was 45mm x 85mm for the metal that would fit the slot although you could trim it down if you wanted. Make sure the metal you use is able to attract a magnetic...

Elegoo MINI Air purifier holder and vat spacer for Elegoo Mars 2 Pro

... The smaller holes are for an m3 screw, with a recces for the nut on the other side and the larger holes are for the magnets. ... Its designed to attach to a 75mm Ducting, i secured mine with zip ties however I'm sure actual clamps would be better.

I realized at some point that the Mercury Plus could be a very powerful magnetic stirrer if the magnets were positioned closer together on the spinning plate. Since I never use the wash feature, this conversion was perfect for me. The stock plate...

Remix of the Elegoo Mars to Anycubic wash and cure station adapter. It was too big for my plate holder, and other remixes were too small, and the lock screw wouldn't clamp securely to the adapter. I shaved off 1mm of each side, 1.5mm off the...

Remix which can be used with the standoffs of the Elegoo mars 2 pro machine. ... 1) thanks shish0r for the original design 2) print the thing 3) return it and push in the M3 bolts 4) mount the adapter to the machine 5) mount the fan to the adapter (one...

The Elegoo Mars printer benefits from the AnyCubic Wash & Cure Platform Holder's sturdy construction and precision engineering. Its sleek design seamlessly integrates with the Elegoo Mars, providing a reliable printing experience. The holder's...

Simple spacer/stop for the resin vat to sit up against. ...For the Elegoo Mars 2 Pro. The first version was too high. ... I have fixed that now.

VAT/resin tray for Elegoo Mars and Saturn and Photon (maximum tray height: 31.5 mm). For mounting, 1 piece of 31-32 mm square wood or a 30*30 mm minimum square aluminum tube is required. 4 wood screws or 4 self-drilling screws for aluminum, 3 mm*10...

These are holders for the tools of the devices: --------------------- - Elegoo Mars Pro 2 - Elegoo Mercury plus These are the following brackets: --------------------- 1x for the Mercury plus basket 1x for holding the plate of the Mars Pro 2 1x for...

The Elegoo Mars measures 40 millimeters in length by 24 millimeters in width. Visual inspection reveals a height of 50-55 millimeters by 5 millimeters (M5 x 50-55 millimeters). Thread specifications include M5 x 50-55 millimeters. ... Files accepted:...

... function at its best, it demands a precise distance to pull up the screen into its flat position. ...A notable height discrepancy exists between the original LCD screen on the Anycubic Photon S and the Elegoo Mars screen, measuring between 0.7-0.8mm.