elegoo build plate 3d models

If you want to use a Mamorubot build plate on your Ender 5, you'll need to adjust the distance between the bolt that pushes the switch of the bed and the switch itself. Print it or purchase a longer bolt. ...Enjoy.

I've shortened the model a bit (so that the build plate can be placed on the edge of the vat, instead of putting it inside), and enlarged its height by around 4mm so that users with new FW won't have to do anything apart from installing the holder :)

This adapter gives Creality LD-002R owners the ability to use their build plate with the Anycubic cure and wash station. To do this, simply attach it to the back half of the adjustable bracket that comes with the wash and cure station. ...You will need...

... ...Edited STL in Blender Extends depth of ear peices to the build plate. - No supports needed for Mickey variant. For Minnie, the bow will need to be supported. Recommended 0.16mm layer height, and 0.2mm separation for support to bow piece. ...

I took the Build Plates for the Lulzbot Taz 5, Lulzbot Taz 6, and the Lulzbot Mini Build plates from CURA and reworked them so they align perfectly in Simplify3D with the build area. *Update - I just updated the picture so you can see what they...

This is my DIY wash station solution for the Creality Halot One's build plate and the IKEA 4.2L container with magnetic stirrer. I typically only use water washable resin so I did not design this for use with the lid; however, the mount is easy to...

4mm z-axis spacer for Flashforge Foto 8.9 resin printer Needed as there wasn't quite enough play when I fitted a magnetic build plate. The two lugs locate into the printer so it says in place with the fitting screw removed. 50% infill used as it's...

... and print just fine. ...One corner points down for better drip control plus you don't even need to screw the build plate onto it because it's pointing upwards naturally. ...Printed it successfully without supports on an FDM machine without any issues.

Printing a 1mm x 1mm cube with a huge raft covering the entire build-plate actually turned out to be a better test than this sieve was. When we tried printing the sieve, for some reason the printer just wouldn't cooperate and instead started churning...

So I made this way too accurate 2D texture of the X1 & X2 build plate for PrusaSlicer.This is just a 2D graphic that more accurately represents the build plate of the Artillery Sidewinder X1 & X2. The texture includes safety symbols,...

I chose the largest flat silicone pad available and applied it generously, enhancing it with "ninja sauce." To note, I use a glass build plate as it complements the silicone well, reducing potential wear over time. Additionally, it prevents fuzz from...

This Clamp is a vital component used to link an aluminum Cookie Sheet Pan to a 3D printer, serving as a reliable build plate. To secure the Clamp firmly in place, two nuts and bolts are required to attach it to the round rim of the Cookie Sheet. Many...

Pay special attention to the placement of the back right corner of the glass, making sure that the binder clip on that side is aligned with the edge of the build plate, taking care not to obstruct the movement of the print head during the printing...

Cutting Guide for Prusa Face Shield RC3 (Requires at least 240x240mm build plate) Brian Khuu (March 2020) mofosyne@gmail.com This is a cutting guide based on the laser cut spec diagram for the replaceable face shield sheets:...

I wanted to make a stable but beautiful building plate holder that, apart from being practical, can show the advantage of multi-color printing. I looked over the offer and made my own version by combining their advantages. Having refined the first...

I have not tested this design as it requires a build plate that is larger than my 200x200mm buildplate. But it may be of use for others. ... faceShieldSheetModel() : This is the model of the face shield sheet faceShieldDrillGuide() : This is the...

Managing a school's 3D printer has led to recent issues with leveling the build plate due to worn rubber pads. A temporary fix can be found here (http://www.thingiverse.com/thing:43050), but calibration remains crucial. To make this process easier, I...

I have not tested this design as it requires a build plate that is larger than my 200x200mm buildplate. But it may be of use for others. ... faceShieldSheetModel() : This is the model of the face shield sheet faceShieldDrillGuide() : This is the...

The resin flows too quickly through LittleRP's extruded build plate, so an end cap is placed to prevent this issue from occurring. This object was printed using Robox with the AutoMaker 1.01.01 software, Cura Slicer, and set to normal print quality...

I think the second rail in the front of the build plate that I added is NOT included in the rails layout off to the side. So make sure you account for that rail when ordering V-slot. Also, you will need more rollers and screws etc for the front rail...

Add the Creality logo, measurement lines, and numbers to your bed plate in PrusaSlicer. To install the .svg file in PrusaSlicer: 1. Click on Printer Settings tab. 2. Under General, click the Set button next to Bed shape. 3. Under Texture,...

Add the Creality font, measurement lines, and numbers to your bed plate in PrusaSlicer. To install the .svg file in PrusaSlicer: 1. Click on Printer Settings tab. 2. Under General, click the Set button next to Bed shape. 3. Under Texture,...

A side note - As I discovered when working on this project, each DVD sled has its unique design and different mounting locations, therefore, new parts will likely need to be made to accommodate your specific DVD drives, making these parts unlikely...

I got tired of aligning my Fulament PEI plate to the Printer bed, so I designed one of these for my printers. It Works really great and even has a Strain relief. Share the love! https://www.youtube.com/shorts/dsJgboF8cYI Good info!! Press the...

Remix of https://www.thingiverse.com/thing:5334643 for increased height at 3.8mm for Wham Bam XTR

Feet, backstop, and slotted brackets are to be printed and screwed to table using #4x1/2" long wood screws. I used 1/4" MDF as my table surface cut at 28"x22.5" but you can use whatever material you like. The grid is to be used when limit switches or...

This spacer addresses a gap between the guide block on the x-axis rail and the bracket mount for the heated build platform on the Cetus MK3. ### Why is it? It's designed to counteract the dent in the fold, visible in the photos. If one screw that...

... The digital dial no longer strikes the side of the rear right bracket while leveling the raised glass plate, resulting in a smoother printing experience. I can now swap out the glass and continue to print without waiting for the cool down period.

The optional “tongue” is a stabilizer that slides under the printer if you're placing it next to the printer.Thanks to all the designers that came before me in the evolution of this design.I've included a Bambu Studio 3MF for the 6-slot version with...

... and wanted to print the front cap in one piece so combined it. It saves some gluing, filling and sanding. 0608_-_combined_cap_front.stl If you want to see more of the build process:https://imgur.com/gallery/Ea5jthttps://imgur.com/gallery/uP80a