elegoo 3d printer neptune 2

This is my "Proteus" printheadcover for a 3-Fan-setup. ... i designed this after encountering problems of "too hot corners". to buy: 40x10mm directionalfan (Creality-3D-40+40+10mm-DC24V-0_1A the one I used) to do: soldering (not hard)

A remix because the original one was mounted from the top and it was wobbly so I made remixed it so it could be mounted using the two mounting holes on the back of the biqu h2.For mounting it you need 3m3 screwsInstallation steps:1-mount the biqu H2...

^_^ Not perfect, I designed this one using Fusion360, and it fits nicely on the side of my Neptune Elegoo 3D printer under the extruder stepper with two M3 screws. The M6 screw is a bit unnecessary, but I was able to include it anyway. ^_^ I made...

^^ not perfect (the first i did on fusion360) but it match to the neptune elegoo hang on the side under the extruder stepper with 2 screw m3. the screw m6 is a bit useless but, it was possible to do it so... ^^ made to handel a 40mm fan (i miss the...

my 3D model of this printer

Fan mount for elegoo neptune 2 printer with two part cooling fans and room for a 40x40x20 hotend fan.

This is an adapter for the "Air Controller for 3D Printer" in conjunction with the riser of the Elegoo Saturn 2 from @gltovar . This simple component can be used to level out the height so that the controller can be operated properly.I glued the...

Hey this is my modified mount for a automatic bed leveler to go with the mini Satsana fan ducked before a elegoo Neptune two, three, 2S, 2D I modified it so that it was easier to screw it in on to the plate otherwise the bottom screw was impossible...

I also have a (low profile) or smaller version, that is not as big and bulky.Link to low profile version:https://www.printables.com/model/324158-elegoo-neptune-2-2s-2d-3-filament-guide-low-profilMake sure to go check out all of my other Elegoo...

Pen holder for Elegoo Neptune 2 / 2S 3D printer Pen holder and depth limiting ring Adapter to increase height limit (Z 18mm) Note: The bracket is designed to be installed in the holes where the BLTouch is placed, so if you use the BLTouch you will...

Redesigned the bracket to work with the elegoo neptune 2 which doesn't have the top channels on the aluminum extrusions. I also modified the case for the screen to allow access to the brightness dial and screen flip switch. Category: 3D Printer...

Designed for use on the Elegoo Neptune 2 3D printer Arms snap into v-slot profile very securely - will need to be slid out or prised out if you want to remove (this was intentional) The LED channel is designed to fit 8mm LED tape, I can design for...

I also have a (low profile) or smaller version that will be in my profile.Link to low profile version:https://www.printables.com/model/324158-elegoo-neptune-2-2s-2d-3-filament-guide-low-profilPrint SettingsPrinter Brand:ElegooPrinter: Neptune...

If you want to support me so that more designs are available for free. Donate Thank you very much and happy printingPrint SettingsPrinter:Elegoo Neptune 2Rafts: NoSupports:YesResolution: 0,2Infill:100Filament:Eryone...

This is [the QuickDraw probe](https://github.com/Annex-Engineering/Quickdraw_Probe) mini dock mount for ELEGOO Neptune 2 series 3D printers. It is compatible with [the Neptune 2 version of the Stiffy...

For this project, your gonna need a elegoo neptune 2 or 2S and a E3D Hemera (full kit) print the part and detach the gear mechanism from the stepper motor on the hemera with 4 screws, mount the hemera to the adaptor mount the hemera to the hotend...

I am using this plate / fan duct on 6 of my Elegoo Neptune 2S printers currently (will post additional pictures). [ Update: 02.11.2022 ] Added a compatible BLTouch plate, "en2bltouchfangplate", to the collection. I may combine plates in the...

This is the Raspberrypi 3 A plus / 3A+ case from guysoft (https://www.thingiverse.com/thing:3394092) customised to fit into the rails of the Elegoo Neptune 2. ... I also added a hole for the camera cable.

Redesigned the bracket to work with the elegoo neptune 2 which doesn't have the top channels on the aluminum extrusions. ... I also modified the case for the screen to allow access to the brightness dial and screen flip switch.

Open Prusaslicer and go to Printer Settings→Bed Shape→set. For texture select load and use “PrusaSlicerNeptune2PlatformTexture.svg”For model select load and use “PrusaSlicerNeptune2model.stl”How I made thisThe platform texture was just a simple...

Work area of 3D printer Elegoo Saturn with VAT, platform and Z-axis rack. ...SolidWorks 2016 and STEP.

Work area of 3D printer Elegoo Saturn with VAT, platform and Z-axis rack. ...SolidWorks 2016 and STEP.

This is a model of the Elegoo Saturn 3D printer. ...I hope to get this printer as my first resin printer. 

Here is Elegoo's version of the Neptune 2 and 2S X-axis Tensioner.. The Stl is missing off their website so here it is...I added the assembly/installation word document as well which has bolts/hardware you will need as well.. Sorry I do not have...

This is an Add on for the Elegoo Neptune 2 and 2S. One File is the Holder for the remote and the other file is for the print head. The support does not require any fixing, it clips perfectly, The button is fixed with 2 M3 screws. if you have the...

This is the new dual 5015 Satsana model adjusted to fit on the Elegoo Neptune 2/2S printer. Please refer to the original thing (https://www.thingiverse.com/thing:5750189) for installation instructions and adjust them according to the following...

This is a model of the Elegoo Saturn MSLA printer.

**A remix of @joeymorgans great design to fit the Elegoo Neptune 2(s) which has no guide rails on the sides of the frame, but only top and bottom.** I added profiles to the bottom of the brackets, which makes it easy to slide the brackets onto the...

Simple cover for the Y axis of the Elegoo Neptune 2. I recommend to use a sharpie to black out the aluminium before attaching the cover and use hot glue to secure in place. Sand and paint it will bring a original look. ...

The Elegoo Neptune 2 had two variations of the X axis carriage plate. One had swept radii across the top, one had 50 degree angles. This is for the swept radii version. The other version I uploaded is for the angled plate. ...Installation video...