electromagnet model

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The lower mount uses an M6x1.0 threaded bolt, and I've modeled this hole at 5mm so I can use a tap to cut in threads. (I like the results better than printed-in threads) There are a bunch of reasons why this is a bad idea... (see the earlier photos...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_bottom_fillet_radius = 1.6 custom_top_port_x_position = -10 use_mouse_ears = 0 custom_bottom_port_x_position = 20...

…unless you got yourself a special edition of a bobby car like a Porsche, Mercedes or the older Audi, VW or BMW models like I got. At most of the special edition you can’t fit the original push bar. I found the design of Klein-laui on thingiverse...

You can use a polarity detector app on your smartphone to figure out which side is North (+) and which is South (-).If you want to risk glue breaking loose and would rather not print the magnets into the piece, then you can just grab the models and...

Once I print and test it, I will update this with the final model and the STL's.\r\n\r\nI'm currently working on a new version with a removable tray for the Pi since I now plan to use a Pi4 with this project.\r\n\r\nI would not recommend printing...

** FUSION360 and STEP Sources are included **** I have my printer into an enclosure and, to save the electronics from excessive heat, I've designed this model to enclose all the electronics at a singe location. These were my requirements: -...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

The tolerances on these can be somewhat tight, but they came out beautifully on my Bambu X1C.Model specific notes follow:cards_box_1.stl, cards_box_2.stl - Print one of each. You can add color on layer 4 or 5 (depending on line height) to make the...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_shape = 6 stencil_size = 40 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

The assembly requires some M4 bolts and nuts, RGB strips, a hot glue gun, and tubing with a external diameter below 13mm (I have used 11mm). If you have any feedback, issues, or suggestions for future improvements please comment in the comment...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

If you're experiencing high stringing, do not worry, give it a blast with a heat gun, then a quick brush with a nylon brush and wipe down with a cloth to get rid of any remaining strings. Exterior Perimeters settingsTo ensure the best results...

So far my failures are in optimizing the printer tuning to keep the model airtight. As stated in the Harvard paper, they printed a form and molded silicone for the soft actuators. I probably should do that too, but I am determined to work with FDM...

http://www.thingiverse.com/apps/customizer/run?thing_id=53235 Instructions Using the following options: crankSlack = 1.8 times smaller gear_tolerance = a negligible 0.1 inch midAxisHolderH = stands at an impressive height of 6.3 inches noteAlpha =...

As of 09/16/2018, I've not yet modeled or printed the capstan bearings, nor have I fully solved how I will drive the capstan. My current thought is to use a drill attached to the underside of the platform, using a belt to drive the capstan. I would...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

... 4 mm have been printed. If you're printing at a 0.2 mm layer height, simply add a color change at 4.2 mm (layer 21).If you're looking to make the game conveniently portable, check out Thessiell's lid. Don't forget to rate and share your make!

I started with the photos of the metal models (I've uploaded those photos to thing:1618843) and went from there. All the design work was done in Moi (Moment of Inspiration). Once I had an escapement design, I ran it as a simulation (unsuccessfully)...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_mouse_ears = 0 pattern_line_thickness = 20 custom_bottom_port_corner_radius = 5 custom_back_camera_corner_resolution = 8...

Print Settings: Printer Brand: Robo 3D Printer: R1 ABS + PLA Model Rafts: No Supports: No Resolution: .15 or .2 Infill: 50% Notes: Tolerances may vary. Please direct message me if you're having trouble in either direction (too weak or too stiff). A...

Some parts need supports for countersunk screw holes, or other parts that are not supported by the model or the bed. Use your best judgement, or use PrusaSlicer and the provided .3MF file, which I have pre-configured with supports in the needed...

**These STL files may now easily be imported into many 3D modeling tools** (including [TinkerCAD](https://www.tinkercad.com/) and most 3D printer slicers) **and combined in whatever form you like**. ### Overview ### **Please note**: there seem...

After that, go to the model tab, and press the "download" button. Please note: the final dimensions of the Lithophane are 56(w)x75(h)mm, which includes a 1mm border around the entire lithophane. </li> <li>Repeat step 2 above until you have all your...

It has a hand rest and i'm rendering the models with left, right and both side hand rests. There are also two versions, one with space for a round and one with space for a square fit trim button. The PTT button on the left is the same in both...

(Not required for revision 2) Scaling: The model as is in the STLs will accommodate most types of earbuds, however it can be scaled down as much as 30-35% for smaller sets. If you use earbuds with an inline control, such as the ones shown in the...

Print the bumper pin two more times (for a total of 3 bumper pins) and print the pusher pin one more time (for a total of 2 pusher pins) Before printing out the ball, slice the model in half horizontally and rotate the bottom half 180 degrees...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_drawing =...

THis also means that if you wanted to try to build a GoN NERD/NERD TKL, H87a, or the Kprepublic XD87 should all be able to fit - possibly with some small custimization to the model. More to come as I sort this out, but the files themselves are ready...

Crawl-back happened to me exactly 2 times in the past year or more of using these reels, but I thought adding this might reduce that risk a bit.I added a model for a Jo-spacer that is useful for some Jobo center cores that don't have that...