electribe 2 3d models

Since I couldn't find a decent stand for my Electribe 2 Sampler, I did one by myself. It is split into several pieces, so it can fit any printer with at least a 200x200mm print bed. There different pieces for the backplate, as I included a blank...

Since I couldn't find a decent stand for my Electribe 2 Sampler, I did one by myself. It is split into several pieces, so it can fit any printer with at least a 200x200mm print bed.There different pieces for the backplate, as I included a blank...

This custom voronoi stand is made to keep the Korg Electribe Sample (or Electribe 2) propped up at a nice 12 deg angle and look good while doing it. One of the supports has an integrated cable holder for the power cable and some headphones. The...

This custom voronoi stand is made to keep the Korg Electribe Sample (or Electribe 2) propped up at a nice 12 deg angle and look good while doing it. One of the supports has an integrated cable holder for the power cable and some headphones. The...

If you would like a Commercial License to sell prints made from these designs, please join me on Patreon: https://www.patreon.com/kazitoad This custom voronoi stand is made to keep the Korg Electribe Sample (or Electribe 2) propped up at a nice 12...

I've successfully replicated the original knobs from Korg Electribe 2 and they fit perfectly in my setup. I printed the translucent ones using PETG with a 0.25mm layer height for added clarity. The other knobs were printed on PLA at a 0.2mm layer...

I was fed up with the overpriced solutions available for the Electribe 2 short key problem, so I created this design for everyone. It can certainly be improved, and I encourage you to remix it and make it even better. I've included a 1mm, 1.6mm,...

Also done with the awkwars rotary selector knob on the early electribe models? ...This knob will help you perform better, without having to find the hole.

Bouchon de potentiomètre sur mesure pour korg electribe (EMX/ESX/ES/....). Moins glissants aux doigts et personnalisables à 100% grâce à sa conception en 3 parties. ... (Modélisation 3D par Sheep Tek).

I got my hands on a used Electribe and didn't like the floppy knobs. If yours has the same problem this might help tighten things up! WARNING! The slots for the knobs are elongated, probably to allow for slight variations of the PCB position. ...

Customized version of https://www.thingiverse.com/thing:4671555 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4671555

Electribe reversed shaft knob for Xoxbox Non commercial use only.

This is a remixit is shared. ...so that even small printers can print it thickness: 1,6mm Model make a filament change for the letters.

2

2

2

2

2

2

2

2

2

2

2

by:xyd Made with Cubik Studio 2.9.480 Beta

The design "Human: 2" was created by Romanov using the 3D modeling software 3DTin.

http://www.thingiverse.com/apps/customizer/run?thing_id=273099 Instructions Using the following settings: Letter depth = 2 Border distance = 5 Border radius = 10 Base depth = 2 Y name 4 = -15 Y name 3 = -5 Y name 2 = 5 Y name 1 = 15 Letter size = 7...

Customized version of http://www.thingiverse.com/thing:345972 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=345972 Instructions Using the following options: type = 9.6 flat = 0 length = 2 width = 2

... walls that are 2 units thick. It also features a top clearance of 0.2, a lid with thickness of 2 units and an edge thickness of 0.5 units, a bottom that is 2 units thick, and rounded corners with a radius of 5 units. ...The box's width is 40 units.

... created using the Customizer at http://www.thingiverse.com/apps/customizer/run?thing_id=29211. ...For instructions, set gridY to 67, gridX to 40, thickness to 2.5, meshSpace to 2.5, meshSolid to 1, and add borders of 3 units in both the Y and X axes.