el campo drawing 3d models

Inspired by US manufacturer pictures and drawings we can find on internet. It is actually design to suit the Axial C10 Chevy but I did my best to let it beeing adjustable for any other vehicles. The real scale of that trailer is 1/16 but is designed...

The TS100 is rated at 17W-65W and I haven't seen anymore than around 3 Amps draw in testing. Update on testing - I had our manufacturing department use this set up for a full day of soldering. Managed to get 4 hours continuous use (350c / 5S in...

I took the wood panel laser cut design from: http://www.thingiverse.com/thing:34570 by Docmooney Even though Docmooney posted his DXF drawings of the wood panels with two thicknesses shown in the names, I used 12mm (1/2" nominal) baltic birch plywood...

remixed from the great work from https://www.thingiverse.com/thing:1681442 see it move https://youtu.be/rTlbqrB86YA -- big wheel: one side glued to the axle, other side tightened with screw (drilled a 1.8mm hole and use a 2mm screw); gear on the...

Regular Ender 3 and other PSU's may work also but I have not tested or been able to find drawings of them. This was designed for mounting on the outside of a 3D printer enclosure, so the electronics do not overheat inside the enclosure. There are no...

Below is a drawing of the sketch with the correct dimensions.Here are the instructions to build it in SolidworksCreate center rectangle centered on the origin Set as construction geometry Add smart dimensions to constraint box Add...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 use_stencil = 1 stencil_size = 40 stencil_shape = 6 stencil_mirror = 0 custom_back_extra_port_x_size = 30...

This is to allow for easy switching of 6V battery to USB power and vice versa, without any alteration on the wiring side.Caution: Make sure your LEDs polarity is correct before you solder them in place (refer to the manufacturer design drawing for...

All of the other ports should be accessible, depending upon the size of your connectors.If you look at the photos, you will see that one of the cut-away drawings shows some mock connectors (Ethernet, keyboard receiver, and USB-C power) in purple. Be...

When the dot is stable and doesn't draw circles, epoxy or CA glue it into position permanently tighten the screws. It is now aligned on the axis. Use APC has a nice video using their tool https://youtu.be/qF-iK_BElBM Remove the K40 lens. Insert the...

Since the battery is expensive and there are only a few because the Deebot D35 is doomed to die out, it was clear to me that the man himself started to draw one who looked amazingly similar to the original. :) I cut open the original battery to...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_x_size = 20 custom_bottom_port_x_position = 20 custom_bottom_port_corner_resolution = 8 stencil_rotation = 0...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_phone_thickness = 10 custom_back_camera_x_position = 0 stencil_pattern_element_overlap = 0 custom_top_outer_edge_chamfer_radius = .6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_camera_corner_resolution = 8 custom_back_extra_port_y_position = 30 custom_top_port_corner_resolution = 8...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: stencil_shape = 4 custom_bottom_port_corner_radius = 5 custom_back_camera_y_size = 20 printer_tolerance = 0.2 custom_case_wall_thickness = 1.6...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: use_pattern = 1 custom_corner_resolution = 8 stencil_drawing =...

Expiration ports are unidirectional flow valves or additional output filters. Fan draws room air through anesthesia viral filter. Fan is powered by 12 volt battery pack or AC adapter.</p> <p>Developmental Testing</p> <p>This PAPR has been tested...

Make the outer two pentagons marked for construction.  b: Make pentagon two 50 cm and the outside pentagon 100cm (you can scale it at the end)c: Draw a line from a point on pentagon one to the corresponding point on pentagon two.d: Make the length of...

http://www.thingiverse.com/apps/customizer/run?thing_id=368375 Instructions Using the following options: custom_back_extra_port_corner_radius = 5 custom_right_port_y_position = 0 custom_left_port_corner_radius = 5 custom_bottom_port_corner_radius = 5...

I make no promises that it will be sized right for any 5-pack of 1¼" fuses, but my suspicion is because the Eaton Bussmann fuse pack has been around for so long (there are lots of people on eBay and other aftermarket marketplaces selling empty packs)...

The flowing curves and geometric shapes seem to shift and change as light catches them, creating a dynamic effect that draws the viewer in. This interplay between form and light is a hallmark of Bittker's work, which often explores the relationship...

Links: Wikipeda Entry ISO7010: https://en.wikipedia.org/wiki/ISO_7010 Colors for safety signs https://en.wikipedia.org/wiki/ISO_3864 Wikimedia source of .svg: https://commons.wikimedia.org/wiki/Category:ISO_7010_safety_signs_%28vector_drawings%29...

The smaller box that draws the tissue from the bottom should "snap" into place as it moves past small "grips/guides" while pushing it down into the slot. There are "rails" on the back so larger box fits snug so that when you pull a tissue, the box is...

And How do I use it?WELL in the contrary of the CADs most of the Makers are used to, Openscad is a programming based method of drawings. It is not that easy to make, but for things that are as customizable as this, it is just the better option! Would...

It sims to over 1400' on an F32 so I might want to try that.I've made some attempts to make this as scale as I can, doing math against a 3 side drawing I found online and the diameter of a Pringles can. This is 1/24 scale, near as I can tell. All...

 PETG is more flexible, and the lock needs that flexibility to work properly.Above is a drawing of the lock. It goes in the bottom of the outside tube. You insert it during the printing of the outside tube by pausing the print at 13 mm, insert the...

=&gt; Discarded Side View of Iteration 1 - notice that the measurements here are off by 0.4mm in Z and XZ! Itteration 2: Avoiding the M4 screw head on the other side seemed like a better idea, yet still the measurements were off Iteration 3 -...

All the measures have taken from my bike (MOMA BIKE) but I created all accessories with more dimensions and if that does not suit you contact me and I will make the drawing with your measures. The rear lights box we are going to used for 2...

He draw us a draft on the whiteboard, and it already looked like the finished one:  Then we went through all the remixes of OTTO and tried to find both inspiration and stl files to inspired ourselves form. Thelmo decomposed the character design an...

Whatever you use make sure the wiring, crimps and E-stop can all handle the maximum current draw from a single outlet (10A here in Australia).The case has been designed so that no screw which is accessible from the outside protrudes to the inside to...