einsy rambo raspberry pi 3d models

Perfectly fits onto the nuts of the GeekPi Raspberry Pi 3 B+ Case, which can be easily purchased from Amazon. ...I carefully attached felt pads to them using a strong adhesive.

A protective case for Raspberry Pi users. Contains mounts for side fans, and slits on base for optional pixel glass for further containment. ...Requires 8 M3nS nuts and 8 M3*16 screws to hold frame together.

Modeled in Fusion 360. ...Used the mechanical specs found in the datasheet https://datasheets.raspberrypi.org/pico/pico_datasheet.pdf Raspberry Pi Pico is available to purchase from adafruit and other fine folks https://www.adafruit.com/product/4864

I wanted something to place my Raspberry Pi camera on so that I could watch my Ender 3 print, but I didn't want to get rid of the acrylic case that it came in.

A simple Raspberry Pi Logo.The main logo file can be printed with a color swap. ... (black, red)The leaves file can be printed in green and glued in place afterward.Enjoy!

Modified version of Raspberry Pi 2 cover fabricated with strategically positioned flanges to enable seamless attachment to high-quality aluminum extrusions, while meticulously designed vent holes achieve enhanced airflow via clever infill placement...

I gave Kaanaslan's RPi3 case a speedy makeover to snugly fit my Raspberry Pi 3A+. Next, I'll likely drill some ventilation holes for extra cooling. ...I also tossed on a custom top with neatly drilled air vents.

The Raspberry Pi Model B+ specifications are provided based on official documentation found on their website. ...This design focuses on the main connectors, excluding the micro-SD port, as it is not an official one.

To establish a UART connection between the Raspberry Pi and Misty, you'll need to bridge the gap by physically connecting wires from the RPi's GPIO pins directly to the Misty Backpack's RX and TX lines.

A showcase for the Raspberry Pi 4 in action, currently under development, yet already providing a solid foundation for housing my trusty OctoPi, precision-printed in clear and sturdy PETG plastic.

Mounts to the left front of a Voxelab Aquila x2 to hold a Raspberry Pi 4b with touchscreen. ...If you run Octodash and like watching what is going on this may help you.

Recently, I required a Raspberry Pi enclosure; however, the 3D printed design from GrabCAD was not suitable. Consequently, I made adjustments. ...I haven't tested it yet, but plan to do so shortly.

This is a quick remix from my Raspberry PI 4 case to fit the new Raspberry PI 5.I added a little extra height and ventilation to allow for the official raspberry pi cooling solution.The added button solution works but may need some filing or light...

The available modules are: * Raspberry Pi * Power Supply * HDD 3.5 * HDD 2.5 I am currently using this setup with: * A power supply * Two Raspberry Pi units * An SSD (HDD 2.5) * An HDD 3.5 To print all components without support, I recommend a 20%...

Raspberry Pi Camera holder, remixed from https://www.thingiverse.com/thing:3950698 You can either use the simple holder (easier to print) or the angled holder (see picture). ...This needs support but gives way more flexibility for camera positioning.

I used this part to mount the official Raspberry PI 7" Display into the baffle of a loudspeaker. ...You need to print four of the small parts and glue them into the frame.

A three part enclosure for a raspberry Pi 3B I have included two outer lids one with the logo imprinted and one with the logo cut out

Modeled in Fusion 360. ...Used the mechanical specs found in the datasheet https://datasheets.raspberrypi.org/pico/pico_datasheet.pdf Raspberry Pi Pico is available to purchase from adafruit and other fine folks https://www.adafruit.com/product/4864

Mounting a Raspberry Pi on an IKEA Skadis pegboard requires only M2.5 standoffs and screws. ...The pegboard's holes are pre-threaded to accept M2.5 screws, simplifying the mounting process.

Modified Raspberry Pi 2 case for improved heat dissipation. ...Edit: December 3, 2016 Additional cutout added for a future RS-232 serial interface port installation, along with GPIO pin rerouting to the exterior of the enclosure.

High-tech enthusiasts can now build a cutting-edge enclosure for their Raspberry Pi 2 Model B using precision laser-cut acrylic sheets that measure 1/8 inch thick.

The designers opted for a compact chip-based wooden case for the versatile Raspberry Pi model B+. ...They built this prototype using an intricate, laser-cut design on a sleek 5mm thick okoume wood plank.

This creation is designed to house our Raspberry Pi devices, which serve as 3D print servers via OctoPrint, at Digital Harbor Foundation. ...It is based on the design available at http://www.thingiverse.com/thing:52312.

Check out this awesome project - a sliding box designed specifically for your tiny but mighty Raspberry Pi Zero bot! ...You can find the 3D printing files on Thingiverse at http://www.thingiverse.com/thing:2004812

A unique accessory designed to showcase your Raspberry Pi Zero in a creative and engaging way, crafted using cutting-edge 3D printing technology to provide a sturdy and functional home for this compact yet powerful device.

Simple friction-fit case for the Raspberry Pi Zero and all its variants. If anyone wants, I can add a camera port hole, screw mounting holes, and/or a GPIO cutout. Category: Electronics

I combined elements from various projects to create something new that suits me perfectly. ...This setup can accommodate three Raspberry Pi units within a standard 19-inch server rack.

Partial list of components used: Raspberry Pi 3 B+ Adafruit PiTFT Plus 480x320 3.5" TFT Touchscreen for Raspberry Pi Extension card WM8960 I2S for Raspberry Pi Adafruit Panel Mount Extension USB Cable - Micro B Male to Micro B Female USB 2.0 mount...

Work on an adjustable Raspberry Pi case design to form mini Raspberry Pi clusters. As an electrical engineer, I'm satisfied with my attempt. I followed Gert's Raspberry Pi dimensions from the forum...

Simple friction-fit case for the Raspberry Pi Zero and all its variants. ... If anyone wants, I can add a camera port hole, screw mounting holes, and/or a GPIO cutout.