eggbert looney tunes 3d models

Continually refining designs through model testing and visualization assistant Still exploring different models and renders to improve the design. assistant Working on fine-tuning the design by experimenting with various models and rendering...

I used supports for upper and lower, but especially the lower you might not need it if your briding is tuned well. The flat portion on the lower section is for a name tag, or if you're fancy edit in an embossed name. For my use I see them left...

Tolerances will need to be fairly tight as the assembly is somewhat complex, so ensure your printer is tuned to print accurately. Please review the filenames, model file comments, and pictures before starting.</p><p>Non-printable parts and necessary...

I recommend using 3.5 mm or 4 mm drill bit in order to be able to tune part alignment. I didn't and then suffered the consequences The 27 SL1S enclosure front bottom vent.stl is not probably needed at all but I had it designed so I printed it Push...

If your printer is not well tuned, you may need to apply some horizontal offsets to get parts that fit together. I recommend 0.4 mm nozzle/line width (except as mentioned above) but nothing in the design depends on single-line walls, so other sizes...

The clock is set by disengaging the spring loaded gear of the stepper motor and tuning the handles manually. The RTC clock chip is only used as very precise 1 Herz Clock source. Here you can find required Arduino code: ...

This is dependent upon your printer tuning.For Covers: NoneResolution: 0.2mmInfill: 15%+ Notes:All screw mounts are designed to fit 2.5mm x 5mm screws OR 3mm x 5mm screws. 3mm screws are what I prefer because I do not like the idea of them vibrating...

Instead of the original case_a.stl print the modified one, print the spacer if needed.Cut off the original fan connector, leaving enough wire lengthRoute the fan wires so that they come out at the front (intake) side of the fanSolder...

The stock Creality stepper was 1.5A, for instance, my 23mm stepper is 1A, I tuned the VRef E1 voltage down to 0.8V. (how-to reference: https://support.bondtech.se/Guide/22.+Creality+3D+CR-10S+Pro+-+Stepper+Current+Adjustment/47?lang=en) 5. After the...

TPU.\r\n\r\nThis design is still in development.\r\nYour input would be greatly appreciated to fine-tune the part.\r\nThanks a lot for your feedback.\r\n\r\nThis design is currently under construction.\r\nPlease provide some feedback so we can...

Having this tuned is key for perfect MMU prints.&nbsp;DISCLAIMERS:I own no rights to any of these designs, I merely combined a lot of them and made some tweaks to accommodate screws and nuts. I am NOT a designer or engineer, simply a hobby enthusiast...

Stay tuned for any tweaks that I may come up with. Intro vid: https://www.youtube.com/watch?v=BUi60u7aqNE This is the final version of my W2D-VI Bronco(ish) 313mm wheelbase body. My main goal with this was working on assembly and fit to come...

Stay tuned for more info on that! Auger bit The auger bit provides two pieces of functionality. The first is that it lets you bore small holes for seeding. The second is that it can be used for weeding. Weeding utilizes the boroscope camera to...

These features would make the design even more functional and stable, so stay tuned for updates. In this lesson plan, students will learn the basic principles of greenhouse design and how to customize a design to fit specific needs. They will also...

With this being new territory, I'm confident there are areas that could use some fine-tuning. Eager to learn and grow in my skills! 😊</s> <|im_start|> assistant Tried out Photoshop coloring for the first time on my RedHarbinger Cover: The Bow. As a...

Obviously, the better your printer tuning the less whittling you'll need to do. Other tools are also basics for any Elecronics tinkerer. Soldering iron, wire,... Drill Set ($9.97) ...

(maybe that's my tuning issue, orientation, or lack of supports)--------------------everything below this line is copied from original that this is a remix of- full credit to the original creator who allowed this remix - (Les...

Retraction should be adjusted for direct drive to <1mm, but this may need fine tuning. If changing the extruder gear size, be sure to calibrate the extruder E-steps. For additional support, visit the Thingiverse page at...

Stay tuned for more sets and pieces, as well as updated rules for all of the previous edition's pieces. (DESIGNER'S NOTE-- A few of these pieces were delicate prints when split, though this could be due to printer issues, so a couple of files may...

PLEASE READ IT BEFORE PRINT!!!): Please fine tune your printer before start printing the card (i.e. good bed leveling). I preferred (two different colors) PLA to print the card but any other material (i.e. PETG, ABS etc.) can also be used. In...

Printed at 0.2 layer height with a 0.4 nozzle.Printing all-in-one:You can use the provided Prusa Slicer project for printing all the pieces in a single printing run, here you will not need to run any tuning other than selecting the correct filament...

... speed with this machine and got .2mm pass on it. On my highly tuned Anet A8 I ran the same test at 40mm/sec and got .3mm. ... There's more info on the SKR 1.4 Turbo here and this page has lots of information on stepper driving and speeds here.

Stay tuned if that's what you are looking for. I will post the enclosure as soon as it is completed (expect around early Jan). <b>UPDATE 08Jan21: The amplifier is now online: <a...

The woodworking-inspired dovetail joints keep everything together and make it more sturdy.See the print instructions in the Print Settings section below before printing anything.Notable FeaturesCan be printed on small printersFriction fit assembly -...

Hyperion case for DIY SlimeVR!The Hyperion is one of the smallest and slimmest cases to date for your DIY SlimeVR Trackers.With its completely tool-less design and tolerances fine tuned specifically for FDM 3D Printers, the Hyperion is both easy to...

The provided 3MF should be well tuned for Prusament PETG and prints reliably here across multiple printers. Recommended Pin Receptacle part: Mill-Max 0401-0-15-15-47-27-04-0 DigiKey Part No: ED1165-ND Mouser Part No: 575-0401015154727 Arrow Part No:...

At the intake end of the rotor there is a 2.5mm hole that is tapped for an M3 screw, a ball bearing with 3mm inner diameter and 10mm outer diameter is screwed into this hole, with a washer as a spacer between the rotor and the bearing.There is a...

Stay tuned for more sets and pieces, as well as updated rules for all of the previous edition's pieces. We've set up a Patreon page for anyone who's interested in helping to fund us so we can keep making free and open sourced games like...

Stay tuned ... ### Questions (so far): 1) I tried to figure out a "good size". The board should be both visible and at the same time not take up too much space. I.e. a person should find space on his/her desk. This idea clashes with the principle...

I've tuned up my settings really well. I've got the printer running 0.2mm layers at a base print speed of 60mm/s. Travel speed is 75mm/s; wall count 3; 20% triangle infill; 200C nozzle temp; 55C bed temp; retractions enabled (speed 35mm/s); for dual...