eflite power 160 3d models
226012 3d models found related to eflite power 160.
thingiverse
This offers a good electrical output power of 160 W with an amazingly good control accuracy. Very pleasant is that the voltage can be adjusted to 10 mV and the current to 1 mA. I had previously built a larger laboratory power supply with the big...
thingiverse
Nose gear reinforcement for Horizon Eflite Havoc XE
thingiverse
This mount is to hold a Cyclone 50mm Centerburner from rc-castle.com. ...The mount is intended for the EFlite F14 Twin 40mm Jet.
thingiverse
This is the float attach bracket for the Eflite Apprentice float, The screws are cheap and will break if tightened too tight and ruin the bracket.
thingiverse
Work in progress This is a close copy of the Eflite Apprentice Control Horns The same ones are used on Rudder, Elevator and the Ailerons. ...The only difference is the screw lengths.
cults3d
The is a cowl for the Eflite Apprentice STS or s15e. Replacement for a crash or just to give the plane a sportier look. New V2 features smoother modelling, cutout for nose wheel, lower scoop for nose wheel screw access and looks, screw holes, hood...
thingiverse
The Pitts 850mm Eflite is a fantastic plane - except for its landing gear. The aluminum is too flimsy and bends excessively. I created this upgrade to be stronger and withstand the bumpy landings that this plane is notorious for. I've installed it,...
thingiverse
This is a precision-crafted radiator scoop designed specifically for the Eflite Hawker Hurricane model. The STL files included are meticulously formatted in Inch units, ensuring seamless compatibility with most slicers. However, if your chosen slicer...
grabcad
This motor mount is specifically designed to fit the eFlite Apprentice 15e, ensuring a secure and stable connection for your aircraft's power system.
thingiverse
These mounts are designed for the Spektrum Firma 130/150/160 esc power switch and attaches it onto the side of the center roof/roll cage support (Part #ARA320273) used in the Arrma 6s Kraton/Notorious/Outcast/Mojave/Senton vehicles. <b>There are...
thingiverse
Replacement Cockpit for my eflite sea fury 480. Print Cockpit part as spiral vase. ... The front and back as regular parts.
thingiverse
I made this because I could not grip the wing locks on the Eflite draco. Just glue these onto the wing locks. Easy to grip now. ... Printed at .15 layer Height
thingiverse
Redesign of the original Blade SR120 battery case by Eflite, a complete reimagining of the existing design. Not yet tested or validated for performance. ... Updated on June 21, 2017.
thingiverse
These are new Canopy and cockpit pieces for my 1200mm Eflite P-47D converted to FPV. ... you need to make 2 "canopy aft left" and glue them to the upper portion "canopy aft" found error in Mirror, fixed
cults3d
A replacement shackle for the EFlite servoless payload release. The fit was deliberately made a bit loose to make it easier to mate the shackle, so the payload item may wobble slightly. If you want a tighter fit, make the hole smaller. This thing...
thingiverse
A tool for attaching wing bolts to an Eflite Beaver aircraft, ensuring that it remains on the bolt and avoids puncturing the wing's film during tightening. ...Created using Tinkercad, you can edit this design at https://tinkercad.com/things/7OiQh5j2nzK
thingiverse
A replacement shackle designed specifically for EFlite servoless payload release systems is now available. The makers of this shackle deliberately created a loose fit to simplify the mating process with the payload item, allowing it to wobble...
thingiverse
The stock EFlite Radian and Night Radian come with a subpar servo mounting setup, featuring short travel and lengthy servo arms resulting in unnecessary flex and control resolution loss (short servo travel utilizes only a fraction of available...
myminifactory
Print everything onto a build plate that adheres well, print the battery ring at 98% of its standard size because foam can expand or contract unpredictably. ...It's easy to get perfect prints this way, then just attach them securely using foam-safe glue...
thingiverse
I design and manufacture custom trunnions specifically for my E-flite model airplanes to ensure precise control and stability during flight.
sketchfab
The web address is http://staircon.com/, and it was exported using ProStair software, which has a license number of 6602.
thingiverse
Customized version of http://www.thingiverse.com/thing:384919 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=384919 Instructions Using the following options: tabSize = 2 hingeWidth = 13...