eero pro ceiling mount 3d models

Eero 6 Pro Ceiling Mount made by request. ...Feel free to make adjustments, just cite your source.

Eero 6 Pro Ceiling Mount made by request. Feel free to make adjustments, just cite your source. Print Settings Printer Brand: Creality Printer: CR10S PRO**Rafts:** No Supports: Yes**Resolution:** 0.4 Infill: 25% **Filament:** [...

A remix of B_RadD, his mount was for the Eero Pro 6E. Mine is for the Pro 6. About 2.6mm shorter. I also wanted to add a way for the cables coming out of the ceiling to be hidden by the AP and allow heat to vent out. After adding the base it was too...

A basic strap for cabinet underside or ceiling mounting of an Eero Pro (original). ...The strap is designed to compress around Eero when fastened to surface.

Eero Pro 6E ceiling and wall mount. This allows for a secure mount to any surface. This design is only for the Eero Pro 6E. The Eero Pro 6 might work but is slightly smaller. When inserting the Eero Pro 6E slide in the larger side first. Then gently...

EERO Mount I wanted to ceiling mount my eero.

Wall mount for Eero Pro.

Securely mount your Eero Pro 6, Tri-band Wi-Fi 6 system with this custom wall bracket. Please note, this product is designed exclusively for the "Eero Pro 6" model. Compatibility with other Eero models should not be assumed. ... If you're looking for...

If you're looking for an Eero 6 (non-Pro) version, check out Eero 6 Wall Mount by gleonard3I use #6 7/8-Inch Wall AnchorsPrint SettingsPrinter:CR-6 MaxRafts: NoSupports:NoResolution: .2Infill:N/AFilament:Generic PLA  Category:...

I couldn't find a wall mount for my new eero pro wifi 6 routers yet so I modeled my own and decided to share. Feel free to make any modifications, just please credit the owner. ...Thanks and enjoy :)

Fits the Eero Pro 6E vertically for wall mount. Pretty simple mount but it fits the contours of the unit well. Lay flat onto the base of the model and it prints without supports in under 3 hours. ...I used PETG as it lives in the garage.

I couldn't find a wall mount for my new eero pro wifi 6 routers yet so I modeled my own and decided to share. Feel free to make any modifications, just please credit the owner. ...Thanks and enjoy :)</p> <h3> Print Settings</h3> <p><strong>Printer...

I was reading through some mounting information on the Eero 6 Pro and saw that it should be mounted horizontally because of the antennas. I couldn't find a good mount so remixed a great shelf for the Eero 5 but used the proper (larger) measurements...

I couldn't find a good mount so remixed a great shelf for the Eero 5 (https://www.thingiverse.com/thing:1368236) but used the proper (larger) measurements for the Eero 6 Pro. I also remixed a version that embeds an electrical outlet cover so that I...

This is a wall mount that fits the Eero Pro 6 wireless access point. This can be printed upside down with supports under the camferred platform, or vertically on face with screw holes. ...

This is a mount for the Eero 6e Pro.  I wanted something that I didn't have to drill into my wall, use anchors, etc.  I wanted to be able to mount it on the duplex outlet (not decorator style) and utilize it facing down.  This made cable management...

Made my own version with cable management under the base for Eero Pro 6 routers.The mount hangs on the power brick, and the extra power cord can be wrapped around the inside/underneath against the wall.v3 is the latestNote: This is a work in progress...

I couldn't find a wall mount for this router at the time. ...So after about 2 weeks of trial and error a good snug fitting design rose up from the print bed and beams of light shined from the heavens and that is good enough for now.

I modified the version of Cramshaft64 and removed the attachment for the US sockets. For wall attachment i added 4 screw holes. ... Print it with supports from the bed

... be assumed. If you're looking for an Eero Pro 6 version, check out Eero Pro 6 Wall Mount by gleonard3I use #6 7/8-Inch Wall AnchorsPrint SettingsPrinter:CR-6 MaxRafts: NoSupports:NoResolution: .2Infill:N/AFilament:Generic PLA  Category: Organization

... be assumed. If you're looking for an Eero Pro 6 version, check out Eero Pro 6 Wall Mount by gleonard3I use #6 7/8-Inch Wall AnchorsPrint SettingsPrinter:CR-6 MaxRafts: NoSupports:NoResolution: .2Infill:N/AFilament:Generic PLA  Category: Organization

... product is designed exclusively for the "Eero 6" model. Compatibility with other Eero models should not be assumed. If you're looking for an Eero Pro 6 version, check out https://www.thingiverse.com/thing:4933197 I use #6 7/8-Inch Wall Anchors

This is a basic wall mount for a non-pro eero wifi unit. It has two prongs on the bottom to hold the eero up and then two loops on the sides to attach velcro so it doesn't fall out. ...

For standard eero 6

Fixed eero wall mount with a spot for a label the original had really jagged edges for some reason this is actually a mix of 2 so I used the regular wall mount from (Wall mount for eero wireless unit" by gpvillamil) and added the spot for a label...

... one that's perfect. ...The original had rough edges for some reason, so I used a regular wall mount from gpvillamil's design and added a spot for a label like MikeMahon's Eero Mount with Label. ...This way, it looks sleek and organized on the wall.

Mount a base station for your Eero network by connecting it to a power source and placing it in a central location within your home. ...The base station will provide reliable coverage throughout your space and support multiple devices connected to your...

Inspired by http://www.thingiverse.com/thing:1370241 by gpvillamil, I designed a mount to keep the eero's default orientation but suspend it from under a desk. Note that the material in your desk may cause interference. The eero blog says "Keep your...

Inspired by gpvillamil's design on http://www.thingiverse.com/thing:1370241, I crafted a mount that keeps the eero in its default orientation while suspending it under a desk. Note that the material beneath your desk may cause interference issues.

Inspired by http://www.thingiverse.com/thing:1370241 by gpvillamil, I designed a mount to keep the eero's default orientation but suspend it from under a desk. Note that the material in your desk may cause interference. ...The eero blog says "Keep your...