edc bit driver 3d models

This is a heavily "in progress" project that I'm publishing now because I've made a decision to go forward with another project, and it would be a bit sad to have this project just laying around so I figured better publish it so that someone can...

The caliper-stop, is a bit loose, and maybe needs to be resize 99.9X% to be tight enough for proper friction-fit. The caliper-slide is near perfect for sliding, maybe 99.99% resize. The eraser-plug, maybe 100.4% for snug-fit. Maybe the...

You may find the Colorprint tool useful if your printer supports the M600 command, but your slicer doesn't support adding pauses: https://www.prusaprinters.org/color-print/ After switching filament colors, the nozzle may not be primed and the first...

It has a new value "length" for lenses that have little space to mount it.10.03.20:-added a .rar with parts that will fit in a 200x200mm printer.-Changed part 10 to fit a bit tighter to part 0826.02.20: updated Arduino code to v1.2.5 now with support...

This allows more detail. Material: printed parts 2x (or 4x) 3x6 cylinder head screws (or bit longer if you have some screws already) GLUE, GLUE, GLUE Instruction: print parts make a filament colour change at the lens. this gives a nice detail<ul>...

... and there ya go. 4 screw locations on each, and a bit beefy. These are the base for the next gen adjustable legs. About 14-16mm Ring: Easy adapter for xTool's air assist and the 14mm 10W modules. ... Beats the silly tape they put in the kit.

I made slotted holes because my printed X mounts changed the dimensions a bit. I have printed, installed and now used this part. Below are instructions on how to set it up. I printed them with 1.8mm wall and 30% fill. I also made a set at 1.2mm...

Moving in further and weighing in at a bit higher with 10k version at an even higher balance with it all still not finished coming together as a unit for those of more taste when it's forged into its ultimate most supreme best from 14k model the...

One for the box fan (It's a bit too loud) and another for the Spindle (safe precaution) Both were add with a soldering iron after the box was printed and that's why there are no holes on the part. :-) The end stop switch holders for the X and Y axis...

I also moved the wing a bit down, I think it looks nicer. In this design the GEARBOX is modified to hold the skull and the wing. V3 → added on 2023/03/21Why this new design? my son just crashed the car full speed on a concrete wall. And the car...

Insert the disk into the plate.This is a bit tricky... A third hand, or fourth, may be useful. ...Using the three stacked plates from steps 7, 8, and 9, assemble them perpendicularly such that the disk slides into the notch present in the side plates,...

Many of you have been asking about this, and it's still a bit of a mystery even after building several multicopters. I hope this helps! Update (2/1/14): I've added battery strap slots to the bottom plate for battery straps. If you're not planning to...

You may want to use a bit of super glue to secure it in place and then the (9 mm!) threaded side sticking out will fit nicely in the Groove Mount Adapter's top. You then just need to add a small piece of tubing (Capricorn preferred), pressing...

Especially the small bits which were a single platter called "smalls". I have deleted nearly all of the support which was originally "baked" into the design work. The design is old, and printers were not always what they are today, as a someone who...

... peg holes on left & right side vertical wood frame. It was a little bit of effort to make this for all 3 versions. I have verified this as best I can, but I could have missed something. ...Let me know if you have any problems with these parts.

If you do print the updated version with (untested) and it all goes well could you upload your make or post in the comments to help out thanks :) hope you like it. There is now an adjusted screen size for a better finishing look, different handle...

To slide the bearings onto the axle, the ends of the cylindrical pin need to be ground a bit. A cordless screwdriver with a chuck and 120 grit sandpaper will do a good job. The bearings should be tight and never too loose. The length of the...

place the spool holder in the bag and push the egress ptfe thru the bag's bowden connector, thru the center connector, and a bit over the top of where the spool will go Use --- 1. connect the bag to the printer 1. spool going in the bag... 1. feed...

My Prusa Mini with a Bowden Extruder system would often grind the filament on the smaller bits of infill until it snapped, due to lots of retraction/deretraction in the same locations. If that happens to you, you can print any of the BOXes on 0%...

Honestly hardest part always seem to be how to get power to the back off the mount cleanly and without making to many holes in the walls. Change Log–- Update 7-21-2024 -- Revamped the model so its a bit more parametric and configurable, which means...

As soon as I finalize all these bits, I'll be sure to add them to the post. One problem that I have in the bottom print is two thin spots that I had to coat with marine epoxy so Bob wouldn't take on water, which won't be an issue if you're adding...

It's a bit thicker (+3mm) to allow you to screw the steel plate on to the Probe Distancer. Use short screws so they don't touch your 4010 fan. PTFE tube length to cut: total 34mm (have tube sticking 6mm out of the Groove Mount Adapter) Never used...

The brackets still work if you have new bits , but intention was to only use stock screws where possible - i'm re-designing a little Of note so far - the bolts that hold into the 2020 extrusion T-nuts should be M5, i sized up M4 The idler holder bolt...

to remove push from the angled face (from the thickest portion) outward and it will release itself from the extrusion.The ideal position is up against the top of the frame, tighten the extruder and make sure your PTFE tube is pushed in all the way,...

I chopped off the mangled ends of the print and glued them in place as a flat feature on this prototype, but there's a better way for those tiny little bits. I might try printing them again with a smaller nozzle, but the 0.40 I printed everything...

- To make the switch fit, cut off the NC terminal, insulate it, and fold the NO terminal across the top - You will need to tap the threads for the magnetic holster mount - The mag spring may need the top u-bend to be squished a bit **Licensing** -...

Model is plenty strong enough but you may want to up the walls to 3 or 4 to hide the infill on the front a bit more.Also if using PETG make sure to use a decent brim as I forgot to increase it and got some warping on the front bracket that mounts to...

You will need all the hardware to reuse on the new housing including the idler latch.Clean up the new housing by drilling out the necessary screw and latch holes and clearing the filament path with a 2mm or 5/64" drill bit.Assemble the new housing by...

Then remove the top 2 wheels completely and press the mount onto the meatal plate until the holes line up nice on the mount and the metal plate (you may need to unscrew right hotend mounting screw just a bit since it barely protrudes out the back of...

Glue together ONE HALF of the base of the gun with its two inner bands (IE: attach the upper and lower bands to only the left half of the base) Do the same with one half of the inner ring and its outer band. Glue the remaining ring inserts into...