ecobee backplate replacement 3d models

This is an entry into the SilverStone Wall-Mounted Headphone Stand Design Competition, a collaboration between SilverStone and Linus Tech Tips. Cast your vote for this entry by downloading it. ...You can watch Linus' video about the competition at:...

I really liked what shilex did with his design, but I had a bunch of keystone jacks lying around so I decided to remix it and add the housing for that in as well.

not much to say it fits good enough

This plate is designed to seal the gap, ensuring that laser beams remain contained within their enclosure. To secure it in place, I employed a door handle from Thingiverse (https://www.thingiverse.com/thing:36465). Two holes must be drilled into the...

I am currently working on this project and plan to add several new images shortly.

A personalized adaptation of the Thing found at http://www.thingiverse.com/thing:118870 was created using the Customizer tool available at http://www.thingiverse.com/apps/customizer/run?thing_id=118870

This is an extremely niche part. If you own a Vanderhall and want to install the JL Audio Bluetooth device in the stock upper hole in the dash, this plate can be placed between the dash and firewall to reduce the size of the hole so that the device...

The customized version of this item can be found at http://www.thingiverse.com/apps/customizer/run?thing_id=118870. Upon personalizing, adjustments were made with Move_Image_Up_Down set to 50, image size at 1, bottom text rotation at zero,...

A specialized protective plate is designed to minimize the impact of RapidStrike attacks.

Connecting a Human-Developed WebCam Solution enables effortless RPI-to-Aspertprint Printer Management from Any Web Location, Allowing Real-Time Visualization with the Reliable Logitech C270 HD Camera Model.

Back cover for masterkey, to cover up the big hole that you sawed off This is after doing the slamfire mod, pictures show where you need to saw off for this part to work. Hardware needed: 2 screws. ...Like those that you won't be using after sawing...

Rear Support for the Eachine Wizard X220 allowing for the maintenance of VTX and RX antennas.

This is a personalized adaptation of the item found at http://www.thingiverse.com/thing:118870. ...It was made using the Customizer tool available at http://www.thingiverse.com/apps/customizer/run?thing_id=118870, which allows for custom designs and...

Switch back plate

<p>The PSP Go uses the same battery connector as the Vita 1000. I found a few extended backs, but they all required taping the battery in place. On top of that, there was no way to access the M2-to-SD adapter from the outside.</p><p>I used Hipcat's...

because i could not find one a stl i made one

Tested with AMD HD7970M and Firepro S7100X. ... I have not tested the newest (uploaded version) yet, but M3x0.5 and M2.5x0.45 Screws should work.

I was unable to install my Nest thermostat in my new home due to a gaping hole that was far too big to fill. To overcome this hurdle, I creatively reworked the back plate of the thermostat so it could be securely screwed into place against the wall,...

Here is the rewritten text: Zotac 1060 6 GB Graphics Card Back Plate.

customized with 3D Slash!

<p>Printed in TPU</p> <p>Back plate to cover the back of a runcam mipi camera</p> Category: R/C Vehicles

Back cover for masterkey, to cover up the big hole that you sawed off This is after doing the slamfire mod, pictures show where you need to saw off for this part to work. Hardware needed: 2 screws. Like those that you won't be using after sawing off...

A quarter-inch socket wrench holds the nut in place securely.

Create a mold for constructing the rear plate of a helmet holder set. Each mold is generated via 3D printing. ...Check out www.TRINOTA.com

<p>this are redesigned back caps for the FGC-68 (MKI/MKII) on the image is a FGC-6 model shown. ...so there is still a hole the remote line in these end caps like the other FGC-68 stocks options</p><p>for all the other stock options look at this...

A ruggedized attachment system designed specifically for the HC-SR04 ultrasonic sensor module demands a substantial increase in its physical dimensions, requiring a scale-up of approximately 1000% or tenfold to accommodate its mounting needs...

Customized version of https://www.thingiverse.com/thing:5320353 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5320353

Control cavity back plate for a Fender Aerodyne Stratocaster type guitar.I do not have an actual Aerodyne Strat so it has not been test fit against the real thing.

Designed this as an adapter for my extruder nema 17 motor to allow the x-axis endstop to be toggled.

Back Panel for ASUS M3A78 Motherboard Print Settings Printer: A602 Rafts: No Supports: No Resolution: 0.02 Infill: 40%