easythreed x1 firmware 3d models

...Enter the pause settings for your printer, my CR10S Pro V2 stock firmware only works with the BQ M25 Method. Standby temperature should be set to your print temperature. * Select "Layer Number" in the "Pause at" dropdown * Set "Pause Layer" to 2 15.

Since switching on the BLTouch code in the Marlin Firmware compile did cause the code size to exceed the memory size of the 8 bit board that I had just installed for the quiet drivers, I changed again to a 32 bit board which works perfectly well now...

If you don't do this, the servo arm will move in the opposite direction you expect when you calibrate it (this may be fixed in a future firmware modification, but for simplicity's sake flipping the connector does work) Assembly steps for winder Fix...

(Open source firmware for ESP devices: https://tasmota.github.io/docs/) (Einrichten von ESP8266 / TASMOTA und diverse interessante Details zu D1-Mini:...

2- The other Firmware without MAX7812 and NeoPixels. You should take care that you have the same board, calibrate everything yourself X-Y-Z-Extruder. This is just to get you started, I will add a pinout in a next update, you can figure out the...

Due to the flexing of the shaft there are definitely some quirks with this extruder but nothing some good slicer settings or firmware offsets should be able to remedy. The majority of artefacts seen in tests to date relate more to Retraction and...

This is somewhat bespoke, in that filing, trimming and etc are all needed Removing the WIP mark now - as only the instructions may change if folks need clarifications Added a hand wiring diagram and firmware example including the source zip if you'd...

I created this project to get more experience in modelling for 3D printing using Fusion 360, practice my soldering skills, and get a chance to do a little ESP8266/Arduino programming. *Features* hang it from the wall using the built in hole(s) or...

:) After being given a broken Anet A8, complete with melted wires, I set about fixing it and upgrading it with Marlin Firmware, level sensor and flexible steel print bed. This is my water pump design; with the main aim being to teach myself 3D design...

If this results an error, then you printer has no eeprom or it is not enabled by the firmware. This however is no show stopper. Create a line containing the gathered calibration information like "M92 X100.3 Y101.2" and add this line to your slicers...

You will have to cannibalize your P802M for parts, visit the hardware or parts bin, drill/rig things for endstops, and likely re-flash the firmware. I replaced Melzi with RAMPS 1.4 because I don't like repetier. Do not tear your P802M apart until you...

If you don't do this, the servo arm will move in the opposite direction you expect when you calibrate it (this may be fixed in a future firmware modification, but for simplicity's sake flipping the connector does work) **Assembly steps for winder**...

The HallON website (Garage Maker Zone aka GMZ) only provides pre-compiled firmware, for some boards only available in Polish. Some information can be found on the GMZ forums, but again, only in Polish (thanks Google Translate!). Since my set-up...

I used a Teensy 2.0 and QMK for firmware. Because I installed the switches and soldered all of them before re-designing the plates, I needed to improvise to get the rigidity I wanted (hence the weird screws in the picture below).</p> <p><strong>Here...

The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to...

I am currently running grbl firmware on a Eleksmaker mana 3 controller board with DRV8825 drivers. I have also tested the keyestudio CNC shield V4 & arduino UNO compatible board with CNC Shield V3. I used 1270mm (50") of GT2 belt for the...

Print Area: 220x220x210 (X/Y/Z in mm) Printer Size: 360x380x440 (X/Y/Z in mm) Features: Using a RAMPS 1.4 board running on Klipper Firmware Raspberry PI with Octoprint LED Stripes with custom plugin for Octoprint for heating and printing status...

I have since replaced both with standard Creality 42-40 and all is good and running really cool.The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. I...

I'm sure it could be done with custom firmware, but what I did was connect the printer to my PC using Repetier, and then using the manual controls figure out what the exact coordinates of the buildplate home were (and how wide I want it). I use...

Programming the microcontrollerThe software used is the cloud-free and very versatile firmware Tasmota by Theo Arends. An already compiled version e.g. tasmota-DE.bin can be used. Reflashing is possible with the software Tasmotizer via USB micro...

Update your maximum Z height to 209 mm and reflash the firmware. All done! Updates 2018-09-28 New files are up. You can build it now. Half-way is pretty easy. Going all the way is not. 2018-09-29 Improved the BOM and wrote instructions. Note...

The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to...

So a pause must be inserted at the beginning of this layer, which can be done by right-clicking the orange “+” button and selecting “Add pause print (M601)”.If you have a Prusa Mini (early batch) and M601 is not working: upgrade your firmware and it...

Have a look at my SpiderBot :) Update 2019-07-21 extended the post print description section. After all the updates to my Anycubic I3 Mega-S printer I'm now able to print this at 100% size! Updates on Printer were: TMC2208 Steppers, Marlin 1.1.9...

;-) FirmwareThe engraver is controlled by an Arduino Mega + Ramps 1.4 board running GRBL 1.1f. These were spare parts I had in my drawer and I wasn't aware of the Arduino CNC shield when I began this build. Plus, the Ramps board seemed like an...

Plastic goes on the top side of the PCB, solder goes on the bottomInstall your MCU either directly onto pin headers (not recommended) or socket your MCU as per these instructionsFlash a test firmware onto your MCUOnce you have the PCB prepped and a...

If this results an error, then you printer has no eeprom or it is not enabled by the firmware. This however is no show stopper. Create a line containing the gathered calibration information like "M92 X100.3 Y101.2" and add this line to your slicers...

Due to the flexing of the shaft there are definitely some quirks with this extruder but nothing some good slicer settings or firmware offsets should be able to remedy. The majority of artefacts seen in tests to date relate more to Retraction and...

The firmware changes were relatively simple, there are only a few comments to tweak. I did however have to invert the direction of the X & Y motors. Uncommenting Z_CLEARANCE_BETWEEN_PROBES & Z_HOMING_HEIGHT stopped the Z axis from trying to drop to...

Fit the fan and connect either to the MOSFET if being used as a firmware controlled Control board cooler or to a 12Volt source that is live when the control board is powered on. Ensure fan is fitted to exhaust air from the box to outside. Make all...