easythreed k1 3d models

k1 max mini tool boxYou will need two 10X3mm round magnets.If the video does not play, use the address below.https://www.youtube.com/shorts/wfMiF3TJhbk

Just added the Creality name to the raiser. ...All credit to the original maker. I printed this on the Creality K1.

... space of Creality's k1 printer. ... After printing, you can use it by attaching the cover of k1 and lifting it up. To use a neodymium magnet, it is designed to use a magnet with a diameter of 5mm x height of 5mm. ... inquiry soonsoon@soonsoons.com

Since I already own a Creality K1 and the Comunity is huge, was it a no brainer to make an adapter for the TwoTrees SK1 to use one of the awesome spool holders made for the Creality...

Once I can locate it publicly I will credit it here.These are solid bed mounts for the K1 / K1C / K1 Max to replace the flexible metal ones that are part of the PRTouch/pressure cell stock leveling system. ...You'd only want to install these if you have...

I created this 45 degree light bar mount do to the poor light given off by the factory 6 light LED strip in the front of the K1 and K1 Max.This print will let you slide a 10mm or 8mm strip of led's to mount on the inside front and sides of your K1...

Uses 2 M10 PTFE couplers and the original screws from the back of the K1. ...This allows you to use a spool or hanger from above the printer rather than turn it around every time you want to change filament.

Needed something to cover these new type of nippers that came with the K1 Max, so i took a shot at making it!Print as isNo support neededBrim recommendedI would add tree supports if you have trouble printing.

Hepa filter for the Creality K1.No hardware needed, it snap on the back.The Hepa filter need to be 100x107 mm. ...Found this on Aliexpress for cheap : https://a.aliexpress.com/_EIKtFf1

Designed a side spool holder for the creality k1 that uses the spool shaft that came with the printer. ...You will need 3 m3 x 16mm screws to attach it to the side.

AlterationRotated the connector 90° for spool mounts with Vertical Nubs.Example:https://www.printables.com/model/579724-reinforced-creality-k1-side-spool-holder-with-fila/comments/1337458Download the spool for original model.

Want to raise you K1 lid so the filament tube is completely uninhibited? look no further. ... This raises the lid 2 inches and bends out slightly to allow even more room for the tube to maneuver.

This eliminates all that and I found keeps the chain from touching the metal slide rods.Both models compatible with the K1 and K1 Max Cable Chain.Updated: As requested I have created a side mounted clip for improved bowden chain travel.Updated: I...

The reworked K1 Sports car is intricately designed and perfect for racing simulations. It features pre-applied textures via 3DS Max's fundamental maps. ...The package includes 3DS, OBJ, and MTL files.

I made this mod to improve the blowing of the printed part and protect the hot end from parasitic cooler flows 12.09.2023 - Added cover stl without K1 logo - COVER_MOD_clean.stl

###[Small-form-factor Forum](https://smallformfactor.net/forum/threads/kibo-k1-3d-printable-case-customizable-expandable-60h-10l.16595/) You will find a more detailed development log about the beginnings of the K1. I am open for any questions or...

... to secure to side of printer using stock holes as the stock screws are not long enough. K1 came with some extra screws in the box that worked. ...Do not use longer than 8mm for bottom screw as it will bottom out in the case, top hole goes through.

Shoppinglist: Pcie Riser choose either one | Dual reverse riser | 180-200mm | | 90° riser | 200-220mm | Extension cable & PC Button | angled C14 to C13 extension cable | 30cm | | Metal Power Button | at least 15cm | Screws & Magnets | 53x | M3x6mm |...

It all depends on the time 😄---Z-axis lead screw knob for quick, manual movement of the bed, without homing.Designed for Creality K1, K1 Max, K1C or any other printer using 8 mm diameter leadscrews.The ribs are quite tight, so your printer/filament...

It all depends on the time 😄---Handles for Creality K1 and K1 Max.I felt that the original handles weren't really in keeping with the printer's style.So here's a more modern honeycomb design that doesn't require a stand and has a good grip.You can...

Low Profile K1 and K1 Max lid Riser. Two parts (4) corners, and (4) Edges. Nothing special required. Just print and pressure fit onto the edges of the lid to raise it up the small amount needed for the stock tube to stop scuffing the lid.You can...

Tools and X gantry should be pushed until they touch XY motors bearings supports to achieve the 150mm belt length.Proceed to tighten the belts (as described in the manual, or as you are used to)Optional you can use the belts tension meter found here...

In stand-mode, the K1's rubber feet hold them nicely in place via friction. Case-mode doesn't hold tightly at all, so be careful when picking it up! I can place it in my bag without worrying that the keys would get squished/broken. When not in use...

... stock Left side of frame & Improve Z-axis stability. Enjoy. BOM Easythreed_X1_Controller_Holder001.stl = Main parts. Easythreed_X1_Controller_Holder_Front_Foot_001.stl Easythreed_X1_Controller_Holder_Rear_Foot_001.stl = Height Adjustment parts.

... side of frame & Improve Z-axis stability. Enjoy. # BOM Easythreed_X1_Controller_Holder001.stl = Main parts. Easythreed_X1_Controller_Holder_Front_Foot_001.stl Easythreed_X1_Controller_Holder_Rear_Foot_001.stl = Height Adjustment parts. ...

The ultimate EasyThreed X1 Mini spool holder for 1 KG spools.

... side of frame & Improve Z-axis stability. Enjoy. # BOM Easythreed_X1_Controller_Holder001.stl = Main parts. Easythreed_X1_Controller_Holder_Front_Foot_001.stl Easythreed_X1_Controller_Holder_Rear_Foot_001.stl = Height Adjustment parts. ...

... side of frame & Improve Z-axis stability. Enjoy. # BOM Easythreed_X1_Controller_Holder001.stl = Main parts. Easythreed_X1_Controller_Holder_Front_Foot_001.stl Easythreed_X1_Controller_Holder_Rear_Foot_001.stl = Height Adjustment parts. ...

I was borring with the design of detergent dispenser in Karcher K1, because all time the bottle drops, with This simple piece you can solve the problem, it is very usable, easy to print and install. I hope you enjoy it. Tenia problemas con el...

This duct fits on the exhaust port of the K1 Max with the charcoal filter in place to connect a 4" hose. It was printed in TPU so it is flexible and fits under the two tabs that retain the filter. ...No screws required.