earth in 3d

Errors in calibration can cause the bearing to fuse. The included STL file is for 0.5mm clearance, and there's an additional STL file for a looser bearing with 0.6mm clearance. I obtained similarly shaped metal bearings with rims for $2.20 each,...

Phoenix Mount: If you've followed Kyo's recommendation in the electronics video, you've gone with this controller board from Phoenix CNC: https://www.tindie.com/products/PhoenixCNC/phoenix-usb-cnc-controller-with-pwm-output/ I can absolutely...

100mm bases in Sector Mechanicus walkway design. If you like my work please consider supporting me on Patreon. Become a Patron! ... Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

If there's any binding remove the optional M3 screws again (green circles)Insert the belt into the Belt Holder in the same positions that you marked in the disassembly step.Flip the printer to gain access to the bottom of the Y carriage.Install the...

You can opt for a single strand with a knot or a loop (which, incidentally, is missing – there should be a notch in the tabs for the loop). I've even attempted using magnets for the center string (not a great plan practically), but you can check out...

However if might work for other multimeters as i have not...

With a well tuned ender 3, I got a perfect snap in fit. - Test whether all buttons are functional. (You can use a simple arduino sketch that prints to the serial monitor when a button is pressed) - Get a sheet of foam, put a thin line of superglue...

Line 1 displays the name "VALENTIN" in bold text. Text color chosen is dark red for high visibility. Lug text distance has been set to 2 units for optimal alignment. Minimal color layer thickness has been adjusted to 0.6 units for efficient printing....

Text Surrounding The Entire Perimeter Using an Overhang with Increased Width of Surrounds Per Line Set Wide, Surrounded: text in each individual lines have all now be surrounded evenly wide from border extruder. Thickness Adjusted Border Width and...

The locking pin is 3mm in diameter and 1mm thick. I want to give a huge shout out to Todd Woolums and Clay Warling for helping test out the different designs until we got them right on the money! Thanks Todd and Clay! Other designs are...

A new 2x2 box has been added along with taller boxes in three sizes (50mm high) - 2x2, 2x4, and 4x4, plus several bins designed specifically for these larger boxes. **Update 19 February 2017** I have replaced the old 38x38_SlideTop_4Div.stl file...

70x25mm Slot shaped bases in Sector Mechanicus walkway design. If you like my work please consider supporting me on Patreon. Become a Patron! ... Some of my other designs: https://www.thingiverse.com/thing:4654378 - Rivet Cutting Tool...

(caps have snaps to keep them on)  LONG BOX   Printed flat (this is the Desiccant Cap Long Box lid)   Fold  Slide the two sleeves on (the sleeves have snaps to keep them in place)   Cap...

Wenn ich Zeit finde, ändere ich das vielleicht mal noch ab in eine Version mit Schalter. Und etwas mehr Spielraum für die Kabeleinführung über dem Aluprofil, das ist zugegebenermaßen etwas knapp, aber es lässt sich montieren. ...

20cm is a great length in my opinion.I designed the case to be printed on a Longer LK5 pro. Thats why the main body is only one big part with the GPU mount seperated for faster printing. That way the case is more sturdy but also incompatible with...

The idea is to place the box in a dark place and uses the sensor to wake the effect up a programmable distance.The fourth generation of the case for Adafruit's Animated Eyes Bonnet for Raspberry Pi provides for an interchangeable solution to protect...

For additional safety do not leave this toy in the cage for extended periods of time. I cannot take responsibility for any injury when using this maze or its associated parts.</p> <p><p class="detail-video"> <figure class="media"> <oembed...

Also i rework the cut for the lcd-display in the cover. ...Additionally ther will be a cutout for an (optional) on/off pushbutton.</p> <p>I will also publish the wirring and the needed parts.</p> <hr/> <p>Eingangsposting:</p> <p>Hier mein Enwurf eines...

Add G29 after G28 in your start gcode and slice some bed leveling STL. I also added a 3mm retraction just before G29 because filament kept oozing while probing. Start the print, the nozzle will most likely be too high from the bed. Use Tune >...

This is a storage box, in addition to my organizer, to enable 5-6 players to this great game. First, though not necessary here, check out and print a set of my organizer to this game (https://www.thingiverse.com/thing:5932452). Then print the...

No epoxy was used in my system. After 24 hours with a full water tank sitting on a paper towel there was no visible water leakage. Results may differ with different filament. The water pump adapter was created specifically measuring the Songlong...

... I Designed This Proprietary Software, Sketchup I used XYZWare, a Beta modeling application from XYZPrinting. I made sure I could export in STL, as I think others might gain from this. ...I also used Google Sketchup for the laminate frame and rails.

However, I find the products that I found online to be cheeky in terms of price. A piece of board sometimes costs €100 or more. That's why I'm currently working on various components that can be printed and then screwed onto the wall. The project is...

As you can imagine, the cards were constantly ending up in a huge mess! Well, not any more! We created this card dispenser to keep things a little more organised, but we soon realised that card dispensers are useful for many games and even for...

To connect the 60mm fan in the PSU you can use an adapter or (what I do) just lever off the original socket leaving the 2 bare pins exposed on the PCB, then connect the fan plug directly on the pins (red and black wires, yellow isn't connected). ...

5-27-2019: This frame should hopefully print without the gap seen in the prior builds. (due to 0.4 mm print head) Furthermore, the arms are now 4 mm wide / tall and should allow for carbon reinforcement. (Air Foil shaped) I would still suggest...

[UPDATE: 6 Feb '24]I have made the following changes in this update (now v1.1)(1) Parts are sturdier(2) Bolt holes are now recessed for CAP head bolts. (Easier to source)(3) Changed the belt attach design(4) Added link to a part to help you align...

Insert the M3 inserts into the small holes in arm_coupler_endcap. 2. Slide the arm couplers onto the arms: - arm_coupler_pivot should be at the balance point of the rods. - arm_coupler_rubberband should be between the pivot and the ends of the...

This 223/556 25 round ammo box was designed in Fusion360 and printed on a Prusa Mk3s+ with eSun pla+. This was specifically designed to be a gift for my pap. I have 5 round boxes as well, but haven't posted them yet. 3mf and gcode files attached. I...

You can see the custom made one in place now. I'm also modding those vents, they don't print very good now. Making them more horizontal than vertical. New print will be ready by tomorrow, I'll upload new models then. 06.11.2017 New top part...