early bronco front bumper 3d models

i designed this sport bumper for the bronco to make it more sport looking but still mantaining some scale look, i also made hole for the bumper lights and a hole for the winch, it is fitting perfect on the stock bumper moun and is not going to bind...

I designed a bumper specifically for my Traxxas TRX4 Bronco, which fits perfectly and features strategically placed holes for secure mounting. Next on my agenda is creating mounts for lights, and I'm particularly interested in incorporating KC-style...

A custom built sleek and much more tucked SCX24 Bronco front hoop bumper. 3D printed and maintains the factory fog lights, just relocated to a more central fog light position. ...This bumper allows for better approach angles and does not interfere with...

This is a set of mounts, to bring the front bumper in and up to the body. ...It is in 2 pieces and replaces all the factory mounts, because the factory mount hits the servo at this location.

This is an exact model of the 2021 Ford Bronco

The Traxxas TRX-4 Bronco Frontbumper is designed with a flat edge that allows for secure attachment using bolts or other fasteners. Otherwise, it remains remarkably close to the original design, allowing the use of the factory mounting points if...

Hello, Here is my two parts to remove de front fake winch support above the front bumper and to conserve the D-rings on your Traxxas TRX 4 Ford Bronco 2021. And increase your approach angle for your Bronco ! Others parts are coming out later ! ... ...

Installation requires no modifications to your vehicle's factory front and rear bumper mounts. However, you will need to purchase tow eyelets to cover the hex screw mounting area. ...To get started with installation, please watch the video below for...

Front bumper for the Traxxas TRX4 Ford Bronco. Integrated mounting bracket in one single file. Requires only two screws, each 2.5 mm in diameter and 20 mm long, along with two matching nuts to secure it in place. This design was created using...

This bumper is for the new bronco hard body. It replaces the big bulky bumper with a slimmer and tucked bumper. D hooks are from the stock bumper. ... I recommend .1 or .12 layer height, will work best with a finely tuned printer because of D hook...

A bracket to put a 4 in speaker in early bronco in original speaker slot.

A cup holder designed to fit in between the front two seats of a 72 bronco. a slot to fit a 4 inch speaker and room to rout cables. ...two slots are implanted to place phones in the cup-holder.

A bumper mount I designed to fit TRA9224 to an Element Enduro chassis

Here's a robust front bumper designed specifically for the Traxxas Trx-4 Bronco, engineered to accommodate an RC4WD 1/10 mini winch system featuring the 9.5CTI WINCH.

This is a replacement front bumper support for the scx24 bronco. ...Removes the gap between body and bumper without raising the body post.

Bronco enthusiasts can now access detailed 3D printing files for a custom column cover. This innovative design boasts an additional cutout situated directly above the steering column, expertly accommodating aftermarket gauge wiring passages. ...To cater...

Bumper replacment for scx-24 Bronco, remove stock bumper and mount, this replaces the whole setup Print flat with no support

The TRX4 Bronco Bumpers are a direct fit for the Traxxas TRX-4 Bronco. these bumper gives improved clearance and the ability to mount up to 4 external spotlights (sold seperately). The design also has a built in fairlead for those with a chassis...

ditch the bumpers and clean up the look. ... will need to scale up 10 times for correct size. front bumper delete - 28.726mm x 34.534mm x 12.7mm rear bumper delete - 22.86mm x 38.608mm x 5.588mm print at 100 for strength

The following designs are still a work-in-progress and represent concepts I have been developing. ...These particular sketches pertain to the front bumper of my 1969 Ford Bronco, and were created using SolidWorks software in 2014.

The TRX4 Bronco Bumpers are a direct fit for the Traxxas TRX-4 Bronco. these bumper gives improved clearance and the ability to mount up to 4 external spotlights (sold seperately). The design also has a built in fairlead for those with a chassis...

SCX24 Bronco High Clearance Bumper designed so the wheels will not rub and gives awesome approach angle. ... The body standoff is set to lowest position.

This is a big stinger bumper for the TRX4M Bronco. 3 M3x10mm screws needed to bolt together. Print at 100 for plenty of strength to lift the car itself. Might need to change the scale to times 10 for right size. bumper should be 28.726mm x 48.768mm x...

front bumper with spotlight holder

Front Bumper for prototype we were working on.

Front Bumper for prototype we were working on.

A 2000 S10 front bumper is required, but the mount positioning remains uncertain at this time.

The front bumper is specifically designed for the M3 GTR model and has been meticulously crafted using 3ds Max software.

I'm merely practicing my text-spinning skills here. ...The subject at hand is a front bumper, specifically referring to its surface.

A revamped front bumper was designed using 3D modeling software, specifically 3ds Max, as part of an exercise to practice skills in virtual remodeling.