eachine wizard x220s 3d models

Moved to: https://www.prusaprinters.org/prints/99976-eachine-wizard-x220s-arm-protection Print in TPU or PETG, replaces the LEDs

Side panels designed specifically for the Eachine Wizard x220s that can be used independently of the standard PDB (Power Distribution Board).

Moved to: https://www.prusaprinters.org/prints/99984-eachine-wizard-x220s-frame-protection Print in TPU or PETG for best protection

Moved to: https://www.prusaprinters.org/prints/99997-eachine-wizard-x220s-antenna-relocation Relocates the antenna to a much more crash resistant location. ... Print in TPU, PETG or ABS

Eachine Wizard X220S XT60 Battery Plug Mount with Antenna Mount - A Sleek Addition to Your Drone's Build.

Moved to: https://www.prusaprinters.org/prints/99969-eachine-wizard-x220s-cinewhoop-conversion-ducts Print in PETG Props need to be trimmed a litte bit

Antenna mount for Eachine Wizard X220S with dual antenna receiver (X6B)\r\nMade specifically for securing with Ty-Rap and heat-shrink tubing.\r\n\r\nSupports a 90° antenna mounting system designed for the Eachine Wizard X200S, accommodating a...

Moved to: https://www.prusaprinters.org/prints/99999-eachine-wizard-x220s-gopro-hero3-hero4-mount Full Protection, about 30 grams. 10, 20 and 30deg angles. ... Print in TPU for more durability and PETG for more cam protection (but will break while...

I utilized my Eachine Wizard x220s racing drone for some stable camera work, so my standard 25 or 35 degree GoPro mounts were not suitable, so I designed and created this custom 0 degree stand. It prints perfectly in TPU flexible material. ... If...

Top and bottom plates for the Eachine Wizard x220s drone frame are easily created with adjustable height settings through scaling of the Axis when slicing the design. ABS prints work but fall short in terms of robustness compared to stock plates. To...

I tweaked a couple of aspects to make it compatible with the X220s from Eachine.

This is a version specifically designed for the Runcam 3S with a tilt of 30 degrees, compatible with the Wizard Eachine X220S. The Runcam 3S stands out from its counterparts, the Runcam 3 and Gopro Session, due to distinct size differences. ...A TPU...

It's a straightforward sketch devoid of any curved lines yet it gets the job done effectively.

its a upgrade for you eachine wizard x220s or x220 when you brake the antena holder. ...also the xt60 holder keep the connector in place...

Mounting this camera is a breeze, allowing for precise positioning on top of the Eachine Wizard X220s. To ensure stability, secure it firmly with a strap directly onto the mount. ...The recommended camera angle is 30 degrees.

These are standard footings for the Eachine Wizard X220S quadcopter. ...To assemble it correctly, you'll require longer M3 screws measuring 9 millimeters, as opposed to the shorter ones that come with the drone at 6 millimeters.

Moved to: https://www.prusaprinters.org/prints/100027-eachine-wizard-x220s-gopro-hero-567-mount Full Protection, 10, 15, 20 and 25deg angles. ... Print in TPU for more durability and PETG for more cam protection (but will break while crashing) Use...

VTX Mount for Eachine Wizard X220s Quad Copter The stock VTX mount is extremely delicate and shatters upon a crash, additionally damaging the antenna as it takes the initial impact of the collision. Consequently, this VTX mount was designed to...

Designed for a BN-220 GPS. ... Need new Screws M3 x 16mm

Relocates the antenna to a much more crash resistant location.Print in TPU, PETG or ABS

This protective cover is engineered to extend the lifespan of your drones' motors and arms. It won't safeguard your propellers significantly (Check images at the end). They also serve as a fantastic gripping spot provided the battery isn't connected...

I've noticed that the X220's camera is prone to sticking out of the frame when used at higher angles. During crashes, objects often collide with the camera lens and cause damage. To address this issue, I designed a camera guard that should protect...

Click the antenna protector into place, then secure it using zip ties or tape attached directly to the antenna. The print is designed to fail during a collision, absorbing some of the impact's energy that would otherwise hit the antenna head-on. This...

<p>Print in TPU or PETG for best protection</p>

After several severe impacts, the primary antenna receptacle on the top plate cracked. The antenna itself often suffered significant damage as well. I'm attempting to mitigate this issue by adjusting the antenna's position downwards. ...This involves...

<p>Print in TPU or PETG, replaces the LEDs</p>

This is new maked mount for gopro. Its more stronger than mount from bonzailyte. Weight its about 7-8g. ...Print by ASA or PA12 for more strengh

Print with high-performance TPU or ultra-durable PETG for maximum safeguarding.