eachine wizard x220 v2 3d models

Cut to the chase, tear it apart, display it.

If you can't print this model yourself, order it directly through my 3D hub located here: http://3dhubs.com/service/8Bit. The original design was slightly too long; check out the link to see a comparison photo of the adjusted holes. ... If you're going...

Minimalist ESC Cover for Your FPV Quad Print time is approximately four minutes. I've crafted a minimalist solution to safeguard your FPV quad's ESCs from damage in the event of a crash. The slits on top will likely aid in keeping the ESCs cool...

This bracket is specifically designed to seamlessly integrate with the authentic GoPro clip mount.

... angle of 45 degrees, all integrated into one convenient unit. ...I've successfully implemented this design in my Eachine x220, with everything functioning smoothly as expected. ...Feel free to give it a try and experience the benefits for yourself.

This is a Antenna Holder for the Eachine Wizard x220. Matching the x220, no approve for hv or s. it also makes the drones ass a little longer, so you can stick in a RC and a VTX (tested fitment with an flysky fs-i6 and a TBS 5.8 hz Unify Pro Race. ...

Here are various GoPro/Xiaomi Yi Action Cam Mounts for the Eachine Wizard X220/X220s, as well as for the much older TC-R frame series. I shot a few different angles. If you need a steeper angle, just shoot me a message. If you don't have a 3D...

Eachine 250 Extreme Motorschutz System

This revised version is designed to optimize the mounting system, ensuring easier zip tie installation and enhanced printability. The design has been crafted using Tinkercad, a powerful online platform that allows for seamless editing and refinement...

I needed a custom case and mount for my Xiaomi Yi action camera to fit snugly on my Eachine Wizard x220. I merged the two designs, using the 25-degree mount, to ensure perfect alignment with the Wizard's mounting holes and matching dimensions. Then,...

I rely on this versatile tool to secure both antennas under the sturdy quad, a testament to its ability to withstand rough landings time and again. ...Print Options Include: Supported Features: Absolutely Anything Goes Infill Settings: Optimized for...

good quality is in PETG full filling on Ender 3 is 1 hour and 7 min. ...happy flight

I attached a sturdy side plate to the device, carefully crafting an additional millionth of an inch to reinforce its central core. ...Without this added stability, the entire assembly felt fragile and prone to collapse.

It's a straightforward sketch devoid of any curved lines yet it gets the job done effectively.

Case Study: Enhancing the Eachine VTX03 with Improved Design. The upgraded version draws inspiration from a successful project on Thingiverse, specifically thing #2426206. This enhanced design boasts increased durability and a more precise fit,...

This is a CommDock designed originally for the Wizard X220, but it fits the Martian 2 or any other similar x220 size frame with similar widths - there are a few. This is my first release of the design. I've held onto this design for about 3-4...

This mount secures a BN-180 GPS to the back of an Eachine Wizard. Printed from TPU, it has endured multiple crashes without issue. ...Onlookers consistently compliment its sleek design.

Mounting this camera is a breeze, allowing for precise positioning on top of the Eachine Wizard X220s. To ensure stability, secure it firmly with a strap directly onto the mount. ...The recommended camera angle is 30 degrees.

These are standard footings for the Eachine Wizard X220S quadcopter. ...To assemble it correctly, you'll require longer M3 screws measuring 9 millimeters, as opposed to the shorter ones that come with the drone at 6 millimeters.

Moved to: https://www.prusaprinters.org/prints/100027-eachine-wizard-x220s-gopro-hero-567-mount Full Protection, 10, 15, 20 and 25deg angles. ... Print in TPU for more durability and PETG for more cam protection (but will break while crashing) Use...

VTX Mount for Eachine Wizard X220s Quad Copter The stock VTX mount is extremely delicate and shatters upon a crash, additionally damaging the antenna as it takes the initial impact of the collision. Consequently, this VTX mount was designed to...

A Hero Mount for the wizard x140hv

I didn't want to see the mountain range in my flight cam, so I took out a small cone of material. ... Print Settings Printer Brand: Wanhao Printer: Wanhao Duplicator i3 V2 Rafts: No Supports: Yes Resolution: Two-tenths Infill: Thirty Percent

I modified the baseplate holes from SteveKfpv's design to reposition the camera mount at a 30-degree angle. A thin velcro strap is required for this setup and prints smoothly with PLA material. ...For optimal results when printing with TPU, I recommend...

Updated the system with enhanced features for the X-M+ receiver, including additional support.

Crafted to connect SMA plugs securely. The VTX and Rx combo functions perfectly on the modified top plate, which features a new mounting system created by removing the outdated holder. ...Please note that these designs are specifically suited for 30mm...

Produced using Esun Eflex material, possibly replacing it with a more suitable TPU option. ...Layer height set at 0.2 millimeters, with a brim applied for added stability.

The tubes extended below the flat bottom of the mount so it would not sit down on the build plate. I extruded some faces and cut everything off to make a nice flat bottom for easy printing. There was also a surface error inside one antenna tube.

Here are some updates to my previous print settings: I've switched to Esun Eflex, which is probably better than the original material. My new print height is 0.2mm with a brim. On July 4th, I added a FoxeerBox2Mount.stl file that allows for a...