eSun filament spool adapter 3d models

This is a quick print for adapting a 49mm spool hole to a 27mm hole. You will need 3 screws to assemble the 2 parts together. ... Also, it can be scaled to be thinner or thicker if you like.

This is a precision spacer designed specifically for use with filament spools. Simply install it into your spool and onto the threaded rod that comes standard with your Anet A8 printer. By integrating this spacer, you can significantly reduce the...

... a 67mm diameter coil, designed specifically for use with my Vertex K8400 reel supports. ...The adapter centers itself around the coil's diameter and aligns perfectly with the smaller spool centering features, particularly the one closest to the K8400.

My design for an Adapter begins with a spool featuring a diameter of 2.375 inches and a shaft boasting a diameter of 0.8125 inches. A lip on the adapter measures exactly 0.1875 inches in depth. Upon completion, this piece will measure 0.500 inches...

The Smooth Running Spool Stand Adapter perfectly fits my stand, making printing a seamless experience. My printer settings are optimized with the following adjustments: **Print Settings** * **Raft Settings**: I have disabled rafts to ensure smooth...

I was a bit unsatisfied with the amount of rolling resistance with the stock setup, so decided to make an adapter that relocates the existing rollers to turn into a hanging spool setup instead. The installation process is a bit tedious, but once...

Filament spools come in a variety of formats, the biggest variable being the bore in the middle. When the bore is much larger than support it is mounted on it may swing around. Combine that with the movements of the printer and non linear feeding,...

Filament spools come in a variety of formats, the biggest variable being the bore in the middle. When the bore is much larger than support it is mounted on it may swing around. Combine that with the movements of the printer and non linear feeding,...

Insert a filament spool with an inner hub measuring 54mm in diameter, specifically designed for one-kilogram spools from filaments.ca. The total width of each part is 60mm, featuring a 6mm spindle hole. This design is optimized for printing on the...

The spool alignment tool adjusts the rotation axis to match the center of rotation on the spool precisely.

Supports not needed.It has a 56mm inner diameter, and to install it, you just disassemble the old cardboard spool, take the sides, and glue them to the respective parts. The 2 final pieces screw into one another.It can be used with filament rolls...

However, all hope is not lost; an ingenious adapter is available that cleverly adjusts the hole size, rendering it compatible with various models such as the Velleman K8200, although its universal application possibilities should not be...

A precision-machined 8mm diameter rod to 52mm diameter spool conversion unit.

I modify a spool with a 75mm hub to fit perfectly onto my Prusa without ever touching its frame. ...By intentionally setting the tolerances slightly loose, I achieve a seamless fit that allows the spool to rotate effortlessly.

This is a Filament Holder Clamp, 71mm outside diameter, 88mm broad,\nclamps around an M7 thread.

... Thing: 605360 on Thingiverse Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=605360 Instructions Using the Following Options: Spool Wall Thickness is Set to 5 Millimeters Spool Hole Diameter is Set to 51 Millimeters

The connection between this adapter and the device it's intended for isn't coming together as smoothly as I'd like.\r\n\r\nI've created an updated adapter with several key enhancements! ...Check it out here - https://www.thingiverse.com/thing:4121018

This spool is designed to use with threaded insertsI used the ones from cnckitchen:http://cnckitchen.store/shared-products/431146823?ref=v1:431146823:-1510512723If you use the “inner - minimal” then a full spool need less than 50g.6x M3-8 screws are...

Adapter for 51mm Inner Diameter Coil Mounting. I Utilize High-Quality Plastic from FDplast in Moscow for Standard Installation on the Anet A8. ...Updated Version Available at https://www.thingiverse.com/thing:4125679

Add a holder to my spool with a 3/8 bolt attached. It features a recessed hole for an RC061008 One Way Needle Bearing/Clutch measuring 3/8 x 5/8 x 1/2 inch on one side. And a recessed area of 1"1/4, X 1/4", followed by a recessed 5/8 x 5/32 for a...

* **Filament Extruding Machine**: This link leads to a filament extruder machine available on Aliexpress. * **Pellets for Extruding Machine**: The final link takes users to pellets suitable for use with an extruding machine on eBay. ... These links...

As it means when you take your spool off of the holder, the spool holder will retain the adapter * This means you can print one holder to stay on the printer, and one for each spool which should stick to the spool * On my Ender 3 V2, a 101% lets the...

... rollers. I utilized a $26 Rosewell dehydrator purchased from Amazon, and this setup performs similarly to the $130 units specifically designed for 3D printer filament. ...A standard 1-inch ACME thread was employed for the nut and platter interface.

Instructions Using the Following Options: Tube Diameter Set to 30 Quality Level: High Definition (80%) Arm End Diameter: 5mm Arm Thickness: 2.4mm Chamfer Depth: 2mm Collar Thickness: 2mm Spool Diameter: 52mm Inner Diameter Backlash Compensation: 1mm...

In addition, you need: 4x Bearing 10x26x8 M5x35 bolt M5 nut

Ender 3 Spool Holder Upgrade to Efficient Filament Management with our Innovative Spool Adapter.

A filament spool adapter for A8+'s spool rod (OD 2 cm) and spool ID 53-57mm. ... To print it for 53mm scale X,Y to 96%.

It's unfortunate that some printer designs may not actually accommodate their corresponding filaments, which I discovered when I ordered an ESUN roll with a standard spool. Therefore, for users with this exact model (60mm), or even larger (65mm),...