e3d v7

BfB extruders/hot ends will be replaced with a 1.75mm E3D-V6 direct drive. A proximity switch will be used for bed leveling. PART 1: The first parts I'll post here are the new extruder carriage and the extruder/hot end mount. I'm reusing the original...

It uses two genuine E3D-V6 extruders, supporting British innovation, so be sure to check sizes if clones are used. The setup can be assembled as a side-by-side or front-and-rear layout and includes an optional 18mm Diameter capacitive Z-Probe mount...

Again, probably not a consideration on the original E3D part. Print Settings: Printer Brand: RepRap Printer: Geeetech I3 Pro Dual Rafts: No Supports: No Resolution: .2 or .3 layer 4 or 5 perimeters Infill: 25% Honeycomb Notes: I printed this in ABS...

Here is version 1 I am working on based on the one made by satoer's E3D V5 hotend carriage. I really like this design and hope others will be able to use it, not just on the Cobblebot but any printer using 2020 rails should be able to use it. It...

Added an alternative e3d v6 (and volcano its adjustable) shroud which can have a DC42 IR sensor attached to it, close to the nozzle to minimise the effect of tilt in the effector when using this sensor. Added a revised version of the bed mounts...

This print took 19.5 hours with settings of three shells, 120mm/s, 10% infill, and 1.2 mm retraction at 35mm/s using a SKR Mini V1.2, BMG extruder, E3D V6 hotend in direct drive configuration with dual Z-rods and pancake stepper mounted on the...

Modified parts from either the Hypercube or Hypercube Evolution have been used for: * 2525 Aluminum Tslot * 3/8 Anodized Aluminum Rod or 8mm steel rods * Z axis design: Acrylic Base or 2020 Aluminum Tslot * Dual Z axis motors * Larger Print Area:...

-Plug the E3D hot end in the E3Dv6 Mount with the heat sink fan. -Set the Direct Drive Part and the extruder stepper motor or the Bowden Part (2x M3x30mm). -Set one end of the belt into the Carriage (the one on the hot end side). -If you go for the...

My custom extruder setup is truly unique - I paired a flying extruder with an E3D V6 hot end, driven by a NEMA 17 motor connected to internal gearing. It's fantastic for printing flexible filaments, easy to set up, and produces outstanding results! -...

### Parts needed: XY joiner: --------------------- * 2 16T toothed idlers * 2 16T smooth idlers * 2 LM8LUU bearings * 12 20mm M3 screws for both XY joiners * 4 35mm M3 screws for holding idlers in joiners * 4 M3 nuts for rod clamps * 12 M3 nyloc...

Parts Required: 2 x Spool Bearing (printed) 2 x Spool Knobs (Printed) 2 x Spool Holder cones (Printed) (4x Optional for 2 spools) 1 x Filament Guide (2x Optional for 2 spools) 1 x 1m, M8 x 1.25mm threaded rod (mine is a Stainless Steel rod) 14 x M8...

I'm using my own stepper motor and an E3D Titan on mine. The supplied stepper cable will likely not be long enough - so keep that in mind before you convert.</p> <p>You will need a selection of m3 bolts and nuts. I'm using 6x 45mm to hold the front...

Parts: Apart from the Diamond nozzle and associated hardware, you'll need three E3D_J6 hot ends and three of everything else! High temp Bowden tube isn't a bad idea, and don't forget to buy some heat-resistant cloth for isolating the Diamond nozzle...

This one was designed for the use of: - Titan extruder (a clone but should work OK with original one) in direct drive - E3D V6 hot end or clone. - Any Nema stepper (I use the original stepper provided with the A8) - 3D touch (a clone of BLtouch) ...

4/ I'm proud to introduce the compact Sunhokey X-carriage for Chinese E3D V5 clones, available on Thingiverse at http://www.thingiverse.com/thing:2259774. INITIAL DESCRIPTION (YELLOW PICTURES): The main challenge was to solve the shaking...

Modified X axis end caps to allow for cantilevered V-Bearings, freeing the sides of the Y rails for case mounting Cantilever Y axis bearings with aluminium plate Build Plate Cantilever Z Axis Dual Extruder (E3D V6) Auto Capacitance Based Z Leveling...

The Afterburner is the latest toolhead from Voron and offers the flexibility to use three different hotends: E3D V6, Slice Engineering Mosquito, and Trianglelab Dragon. It features the inner workings of a BMG dual drive extruder and a pancake...

Print Settings Printer: e3D BigBox Rafts: No Supports: No Resolution: .30mm (top, mid, bottom) and .10mm (neck) Infill: 50% Notes: FoxSmart silver PLA; 195/70 temp bottom part, 200/70 temp mid part, 205/70 temp top & neck Resolution for bottom, mid,...

FAQ: http://www.thingiverse.com/shivinteger/about [>>>] Generating Attributions log: [0] Thing Title: Right Hand robot InMoov [0] Thing URL: http://www.thingiverse.com/thing:18940 [0] Thing Author: Gael_Langevin [0] Thing Licence: Creative Commons -...

Handiemen's duct seemed like everything I needed; however, it was for a regular E3D V6 and he had flipped the effector plate to make it fit. I needed the main features of his duct. The directed air via the new ducting and a way to stubbornly hang on...

3.I am not sure how the pointless oversized connector that comes with the thermistor cable of the E3D V6 original version will work in context to the wire management routes, I still need to try this. I may use a long lead and another thermistor if...

However, the design can be easily adapted to other printers (for instance Prusa I3) and different hotends (a version for e3d v6 is planned). The idea behind this design revolves around rotating the inactive hot end out of the bed using a servo motor...

M3 x 40mm DIN 912 Screws (8 required) Purchased Parts Sources Idler Pulleys, Both Smooth & Toothed >>Gates: (Multiple sources available) [Source 1](https://e3d-online.com/products/gates), [Source...

Ender 3 compact mount for E3D Hemera The aio mount version(recommend) will keep the x offset of nozzle unchange and maximum the X build size is 235mm. This version only use 3 m3x7mm button head bolts to mount the Hemera to the plate.</li> <li>You...

This is a disassemblable 3D printer enclosure I custom-built for my E3D BigBox printer, but you can easily adapt it to fit any other size printer. It can be taken apart and stored when not in use. The concept is straightforward; the case is...

Here's an early test video: https://goo.gl/photos/ZvNmUdDvC9jRPmzk7 It's worth noting that I would recommend getting a genuine E3D hot end to make the most out of this setup, Considering you will have saved money by opting for cheaper alternatives,...

Print Settings: Printer: Repetier/Davinci with E3D Extruder Rafts: No Supports: No Resolution: 0.2 mm Infill: 50% Notes: This endstop is designed for mounting on an extruded aluminum bar using screws and TEE nuts. Print the CAGE and ELEVATOR; these...

One Thing I Found Out Is That with a More Focused Air Flow, It Can Affect Hotend Temperature Stability, So I Changed to an e3D V6 Clone Heatblock and Matching Silicone Heat Block Sock. This Has Been Great for Keeping a Stable Hotend Temperature, and...

... is running, but a PETG one will be damaged after running an ABS print involving higher temperatures and little to no airflow. I've not personally done any testing to determine how much having an E3D sock may protect the nozzle from radiated heat.

+ [4pcs MR95ZZ bearings](https://aliexpress.ru/item/32834097040.html) + [short Nema 17 drive](https://aliexpress.ru/item/4001084479755.html) + [short piece PTFE tube id2 od4](https://aliexpress.ru/item/10000349517368.html) + Nuts and screws: 1pcs...