e3d v6 fan upgrade

This revised version incorporates several improvements over my original "Adjustable E3D V6 improved fan adapter and modded Prusa MK3 Layer Cooling" (https://www.thingiverse.com/thing:3512817). The redesign is a remix of thed0ct0r's "E3D V6 improved...

40mm fan mount for the All-Metal E3D v6 Hot-End to Velleman K8200/3Drag standard filament extruder.Fan duct snap on reusing original extruder screws and spacers, optimized for robustness and easy print.The 40mm fan is more quit than the standard 30mm...

EN fan duct for eMotion Tech's Micro Delta Rework mounted in E3D V6 Very light (6.6g), easy to adjust and install (only one screw) Hardware : one blower fan 4010 one M3 square nut one M3 x 8 mm screw https://www.youtube.com/watch?v=7k_baMUQ2sg ...

... I would try to print everything with the stock hot end before switching over to the E3D v6 hot end. It has its own learning curve. The Fan Shroud Clamp and Zero Offset Bracket are the originals from USWaterRockets. ...See the remix info.

I would try to print everything with the stock hot end before switching over to the E3D v6 hot end. It has its own learning curve.** The Fan Shroud Clamp and Zero Offset Bracket are originals from USWaterRockets. ...See the remix info for more details.

For the E3D V6 groove mount you will need the following hardware: 2 each, 3mm square nuts 2 each, 3mm x 8 screws 1 each, M3 x 25 screw and 1 M3 nut For the fans here is the hardware: 8 of the 3D printed washers above (optional) Top: 4 each, 2mm x 8...

For the E3D V6 groove mount you will need the following hardware:2 each, 3mm square nuts2 each, 3mm x 8 screws1 each, M3 x 25 screw and 1 M3 nut For the fans here is the hardware:8 of the 3D printed washers above (optional)Top: 4 each, 2mm x 8 and 4...

A custom mount combines an E3D v6 hotend, a BLTouch probe, and a 40mm part cooling fan to optimize print quality.\r\n\r\nInspired by previous designs, this creation offers a unique solution for those seeking improved performance.\r\n\r\nNote: This...

Although I haven't tested it on a real E3D V6 yet (it's still en route from eBay), it fits perfectly with a printed E3D model. The test prints shown were created using 0.2 layer thickness and 10% infill for initial fitting verification; final...

This is a custom fan duct designed for my E3D V6 Clone setup, which simply clips over the cooling fins for a snug fit. The tight seal supports not only its own weight but also the stock Anet A8 40 mm cooling fan's weight. I pair it with this...

The custom-made fan shroud has been designed to utilize the same fan used previously, but with an added benefit of cooling the part as it prints. After extensive testing, I'm pleased to report that it's working flawlessly. Print Settings: Printer:...

If you want the regular V6 duct or want to try it with the fan closer to the stepper motor, head over to Hangtight https://www.thingiverse.com/thing:3078853, download his STL-files. ...Mirror the models before printing so the fan is on the right instead...

This is an ultra-compact remix of the fan holder by saldot, designed specifically to fit an e3d v6 while accommodating almost under my Kossel effector. The original design was too wide for my setup, cutting into the print volume and interfering with...

I added a second part cooler fan and added a grill for a more secure connection to the hotend. ...This is made for a E3D Volcano Hotend.

I downsized this Anthony Wob E3D fan duct to fit my 3D printer's enclosure, as the original model was slightly too large.

The heat-sink fan on the E3D V6 draws in air from all directions. This can lead to localised cooling of the print and Heated Bed. The is especially noticeable when printing at high temperatures. This fan shroud ensures air is drawn from areas away...

I swapped my stock hot end for an E3D V6 using Cobratronics' carriage. I had been using Lokster's semi-circular fan duct on my old setup and liked it, so I wanted to use it on the new one too, but it didn't fit. I fired up Tinkercad and made some...

It fits better my cheap E3D v6 Chinese hot end. Improved airflow to cool the hot end has been achieved. A stronger belt holder has also been incorporated. The screwless fan holder and duct feature allows the fan to simply snap inside the frame. The...

This new fan shroud is designed for the Printrbot Metal Plus when using the E3D V6 hotend, coupled with the factory PB Alu Extruder Block. It utilizes the original 40mm fan supplied with your printer but requires M4 screws that are approximately...

This is a dual 5015 fan cooler designed specifically for E3D hotends, potentially compatible with various other carriage models - testing was not conducted. ...The fans are precisely press-fit into their designated holes.

This system features an integrated Extrudercooler designed specifically for E3D Hotends, as well as Jhead and Hexagon models. ...Attaching three 40mm fans is a straightforward process - two fans cool the filament while the third cools the Hotend.

E3D V6 Clone fan duct designed for easy installation by clipping over cooling fins with a 22.3mm fin diameter. This design is specifically tailored for use with this E3DV6 universal mount: https://www.thingiverse.com/thing:2099577 Instructions:...

I've printed a few part fans for the E3D-V6, but this one looks worthy and will stand the test of time! It's strong where it needs to be, and the clip holds great. I had a problem with the angle of the blower fan on the original, and I hated using...

Designed to improve part cooling with E3D hotend and heatblock, but will also work with stock hotend assembly.Duct geometry is based on the Mosquito Fan Shroud by 4nthonylin. Please refer to his model for information regarding air flow...

... 35 degree inclination. ...To create this object I took the extruder created by MadHatter3D. (https://www.thingiverse.com/thing:4070979) The fanduct is designed for my E3D v6 hotend. ...If anyone wants to change this fanduct I've added a Fusion360 file.

... a versatile platform for experimentation. The adjustable height setting allows for precise calibration, ensuring optimal performance. Additionally, it seamlessly integrates with the E3D V6, unlocking new possibilities for 3D printing enthusiasts.

Mount for E3D V6 bowden extruder with fanduct for 5015 blower. Also there is mount for 3D touch or BL touch.<br><br>For assembly is needed M3 screws and M3 heat inserts.</p><p>Print material: ABS (or PETG)</p><p>UPDATE 1: BL touch/ 3D touch holder is...

Mount for E3D V6 bowden extruder with fanduct for 5015 blower. Also there is mount for 3D touch or BL touch. For assembly is needed M3 screws and M3 heat inserts.UPDATE 1: BL touch/ 3D touch holder is now higher. ...Also I added ring for tie cables.

Mount for E3D V6 bowden extruder with fanduct for 5015 blower. Also there is mount for 3D touch or BL touch. For assembly is needed M3 screws and M3 heat inserts.UPDATE 1: BL touch/ 3D touch holder is now higher. ...Also I added ring for tie cables.

This project started with a remix of a popular design made specifically for the standard E3D V6 30mm fan, which I then adapted to accommodate a larger 40mm fan. One of the key features of this mod is its adjustable height setting, thanks to the...