e3d v6 direct drive

Just my design of a E3D v6 Direct Drive upgrade for my Anet A8. No firmware flashing required, just a straight replacement of original extruder system. Enjoy ! ... All parts have been printed on my new Artillery Sidewinder X1 in 0.2mm layer height with...

Just my design of a E3D v6 Direct Drive upgrade for my Anet A8. No firmware flashing required, just a straight replacement of original extruder system. Enjoy ! ...All parts have been printed on my new Artillery Sidewinder X1 in 0.2mm layer height with...

Anet A8 E3D V6 Direct Drive. This printer is a 3D powerhouse that's taking the world by storm. With its robust build and direct drive extruder, it's capable of producing high-quality prints with ease. You can also find similar instructions below on...

I've taken the original design by Ben White and reworked it to seamlessly integrate with E3D V6 hotends, including clones that feature a bullseye-style duct.

This is a direct drive setup featuring the Bullseye V6 with its original extruder and stepper motor intact. ...The Bowden connector from the E3D V6 kit was employed to secure the short Bowden tube in position, providing a seamless integration of...

Conversion to Direct Drive for CR-10 V1 with E3D v6 Hot End. Does not limit X Axis Slight modification https://www.thingiverse.com/thing:2494642 Mounting steps: - print and mount. ... - extend the cable from the extruder motor - move the Z axis...

I then wanted to make it into direct drive, so I created a mount that will attach to the top of the drive plate, and you use two screws and washers to attach it to the original back board holes. I used a BMG clone for the extruder, and a short PFE...

I'm currently assembling another Anet A8 E3D V6 direct mount carriage. ...Once finished, I'll be putting it through a series of tests to see how well it performs.

It implements a direct drive extruder and integrates it with an E3D V6 mount, all in one single component. The stepper motor is mounted sideways and stays out of the way of the rails, so it doesn't cause any loss of print area. Additionally, this...

A direct drive carriage designed specifically for Anet A8 (or other 8mm rod 45mm space i3 style machines) mounts an E3D v6 or clone hotend and a block-style inductive sensor. Why did we choose this design? The Fanduct is actually a minor...

The result is a rock-solid build that perfectly pairs the E3D V6 hotend with a robust 5015 fan and a stylish light. You can find the same light I used here: http://a.co/7q8d69D, http://a.co/2nyPGR8 - it really makes this build shine! ...This was just a...

I'm drawn to the straightforward simplicity of a direct drive, yet I've always been captivated by the sleek lines of the Fang design. ...However, after searching far and wide, I couldn't seem to find exactly what I had in mind, so the logical next step...

This is a remix of AxMod's i3 E3D v6/Lite6 Direct Drive Mount for Migbot/Electron Prusa i3 printers (http://www.thingiverse.com/thing:1119606). This mod makes it possible to use Chinese-made E3D V6 hotends. To get everything set up, you still need...

This is an updated version of my Anet A8 E3D V6 Direct Drive remix (https://www.thingiverse.com/thing:3913249). The extruder motor mount can now be removed with two M4 screws, providing a sleeker appearance when in Bowden mode. For easy removal,...

Thanks to Core3D_Tech for the belt grip used in the linear actuator https://www.thingiverse.com/thing:2829675 This is a simple but effective hotend support for the E3D v6 and Volcano direct drive using linear rail (MGN12H) on the X axis (without the...

I came across devonyyc's ingenious design while searching for a carriage that could handle both direct drive and an E3D V6 seamlessly. However, one thing caught my eye - it was a 4-hole design. With ease, I simply swapped out the two holes for a...

Here's a basic three part direct drive extruder for your E3D V6 and other J-head hot ends, utilizing the SC8UU Bearing Blocks. A mount for an auto leveling probe is in development, with updates to be posted as soon as it's available. This build was...

The Mustang Geeetech Direct Drive E3D V6 v4 = No major changes from v3, added cable route on the bottom to route the heater cartridge and thermostat inside. Added a nut housing holder for the touch leveling device. Added graphics The Mustang...

Convert your Ender 5 / Ender 5 Pro to direct-drive by combining some of the best components available for 3d printing: the BondTech BMG extruder and the E3D V6 hotend. No compromises: This adapter has been specially optimized for the E3D V6 /...

I'm using a direct drive setup on my A8 with stock extruder motor and parts cooling fan. The build is designed for fan nozzles intended for the stock extruder. I added a small post to attach one of the wire clips from the A8 kit for strain relief. So...

This is a support for Alfawise printers to switch to DIRECT DRIVE and can accommodate the extruder from Trianglelab model E3D V6 This support is mounted on the original plate and allows you to install the BMG extruder + Nozzle fans + Radiator, the...

From his profile, navigate to 'Solidoodle Press E3D V6', which should appear under his repositories section on the left-hand side of the page. Now that we've navigated to the main project folder for Solidoodle's 3D Printer, go ahead and expand...

I designed a custom mount for the FolgerTech i3 2020 to secure an E3D V6 hot end. This mount includes provisions for attaching a BLTouch sensor and offers additional mounting points on the opposite side for installing a fan or other accessories as...

This is remixed from https://www.thingiverse.com/thing:3247870 and is compatible with https://www.thingiverse.com/thing:2494642 Basically i loved this guy's mount, but i wanted my printer to remain direct drive on the linear rail setup. So i modified...

This is remixed from https://www.thingiverse.com/thing:3247870 and is compatible with https://www.thingiverse.com/thing:2494642 Basically i loved this guy's mount, but i wanted my printer to remain direct drive on the linear rail setup. So i modified...

I swapped my stock hot end for an E3D V6 using Cobratronics' carriage. I had been using Lokster's semi-circular fan duct on my old setup and liked it, so I wanted to use it on the new one too, but it didn't fit. I fired up Tinkercad and made some...

This is remixed from https://www.thingiverse.com/thing:3247870 and is compatible with https://www.thingiverse.com/thing:2494642 Basically i loved this guy's mount, but i wanted my printer to remain direct drive on the linear rail setup. So i modified...

... I created a version of my own using the original 4020 fan. This should work with any setup where the V6 is mounted in the extruder since it utilizes one of the extruder fasteners, just like this example at https://www.thingiverse.com/thing:3721746

E3D V6 direct drive by 3Displacement suitable for v-slot x axis

This is the Anet A2 X-Carriage for E3D V6 Hotend Direct Drive and MGN12 Linear Rails.